2013 Mercedes-Benz GL450

I bought the vehicle with 104k miles. When hooked to a computer it shows 177k. The odometer was tampered with

NHTSA ID

11739325

Incident

Dec 23, 2025

I was driving along in my 2013 MB GL450 with the M278 engine when the engine stopped. I had it towed to my home and checked it out. I had a suspicion the engine was seized. I eventually had to towed to my closest MB dealership for evaluation. The engine was seized. Their further investigation revealed that a wrong oil filter had been installed when the oil was changed 5 months and 3000 miles earlier. I tried to find out what this wrong filter would cause. I asked the dealership and then MB and got no response. I suspect if this filter caused the issue it would have been an oil pressure issue. The car gave no indication of anything wrong prior to engine seizing. I got no message on the display and when switching on the switch there is no indicator on the dashboard to indicate anything about oil pressure. There is no "oil can" that pops up red indicating an oil pressure issue. To this day have no idea why the engine seized other than an improper oil filter.

NHTSA ID

11724243

Incident

Aug 15, 2025

While driving on the freeway, we picked up a big screw in our tire which immediately deflated. To continue our journey, we wanted to replace the tire with the spare wheel. To do that, we used the floor jack that came with the car and this would have been it's first use. While attempting to lift the vehicle, the threaded bushing of this scissor type floor jack completely stripped (see picture). Not only is this super dangerous to have such a floor jack included, but if could have left us stranded for a very long time in case we would have been more remotely. I would suggest to investigate these floor jacks whether the pose any safety hazards and if make Mercedes-Benz replacing them free if charge.

NHTSA ID

11607649

Incident

Aug 2, 2024

I am reaching out to bring to your attention a significant manufacturing flaw in the Mercedes GL450 model, which poses a severe risk to both vehicle functionality and passenger safety. The issue pertains to water infiltration into the battery compartment situated beneath the front passenger seat and concealed beneath the carpet. Even minor rainfall or streetwater has been found to breach this compartment, causing extensive damage to the vehicle's electronic systems. This results in highly precarious and unpredictable behavior, endangering both occupants and road users. As a poignant example, my own GL450, a 2013 model, has exhibited alarming symptoms. Despite being securely in "PARK" mode, upon simply opening the car door, it displays a distressing message: "Transmission Not in P Risk of Vehicle Rolling Away." Furthermore, the transmission intermittently ceases to shift from "P," presenting an imminent hazard to myself and my children. Despite numerous attempts to engage with Mercedes Headquarters regarding this critical matter, regrettably, they have declined to address the issue, citing its expiration beyond the warranty period. However, extensive research indicates that this flaw is pervasive among GL450 owners, as evidenced by discussions on various automotive forums, such as: [XXX] [XXX] I am profoundly concerned about the gravity of this situation and implore you to take immediate action to rectify this widespread issue. Please feel free to contact me at your earliest convenience at [XXX] . I am more than willing to provide further details regarding my experiences and observations. I earnestly anticipate your prompt response and resolution to this matter. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11579182

Incident

Mar 1, 2024

The contact owns a 2013 Mercedes-Benz GL450. The contact stated that the vehicle was parked; however, while opening the door to enter the vehicle, the message "Transmission not in P, Risk of Vehicle Rolling Away" was displayed. The contact turned off and restarted the vehicle, and moved the gear shifter in and out of park(P); however, the failure persisted. The contact stated that other unknown messages were displayed. Additionally, the contact stated that he became aware that there was water accumulation underneath the front passenger's side seat. The contact stated that there was water on the battery and electrical wiring. The vehicle was towed to the dealer to be diagnosed. The vehicle was not diagnosed or repaired. The Insurance Company later informed the contact that the water had frozen because the dealer had not diagnosed the vehicle or drained the water. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 78,000.

NHTSA ID

11578908

Incident

Mar 1, 2024

Mileage

78,000 mi

SUROUND CAMERAS ARE NOT ABLE TO SEE AT NIGHT AND BACKUP LIGHTS NOT BRIGHT ENOUGH TO SEE.

NHTSA ID

11548083

Incident

Oct 2, 2023

The contact owns a 2013 Mercedes-Benz GL450. The contact stated while driving 35 MPH, the steering wheel became difficult to turn. The contact stated there was no warning light illuminated. The contact had experienced the failure five times. The contact took the vehicle to the local dealer however, the technician was unable to duplicate the failure. The vehicle was not repaired. The contact took the vehicle to an independent mechanic to be diagnosed. The contact was informed that the steering shaft needed to be replaced. The vehicle was not repaired due to the parts being on backorder. The manufacturer had been informed of the failure. The failure mileage was approximately 106,000. The dealer stated the steering shaft failing because of corrosion. At this moment they suggested the part is not available so they wanted to fix my car with a used part.

NHTSA ID

11535803

Incident

Jun 1, 2023

Mileage

106,000 mi

Exhaust valve not working properly and the result of an engine misfire. Mercedez sent us a warranty letter to extend the warranty for this issue 6 months after our warranty expired even though you can find online this has been a known issue for our model of car and year, GL450 2013. There are tons of online forums and threads from Mercedez Benz owners about this manufacturer issue. This should not fall under purchasing an extended warranty or in our case a $17,000 bill to fix the issue on a car with only 70,000 miles on it. This should be a recall.

NHTSA ID

11528865

Incident

Jun 15, 2023

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint A popup is seen on the HU with the message "data connection temporarily not available". Potentially affected functionalities in NTG4.5, NTG5 1.Weather 2.Local Search 3.IP Radio 4.Send2Car 5.Speech Detection Service 6.Navigation 7.iHeartRadio 8.Traffic Cams Cause MB Apps is sundowned for all vehicles with NTG4.5 and NTG5 Head Unit Variant. Remedy No support available for NTG4.5 and NTG5 Head Unit Variants for MB App related topics. Note: Please do not create TIPS. Please do not replace any components. HU/Hermes SW update / SCN coding will not fix the issue.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.