2016 Mercedes-Benz GL450

Panoramic sunroof spontaneously shattered at some time between 2/4/26 and 2/5/26. Car was fine when I drove on 2/4/26 and parked at home at approximately 4:30p (still light outside). I got in car next day 2/5/26 at approximately 5:45p (when dark outside). Heard slight air/wind noise as pulled out of driveway and started driving. Looked up and saw sunroof completely shattered (but still fully attached). No glass inside car until the next day when the sun came out and glass started to fall in and create a hole in the broken glass panel. I was the only one who drove the car. Dealer viewed on 2/9/26, and provided repair estimate of $4,500.30. Still waiting on insurance to authorize repair. I have attached photos from 2/5/26 when discovered and next day 2/6/26 after hole formed and glass started falling into car (blocked by sunshade).

NHTSA ID

11731672

Incident

Feb 5, 2026

Tailgate sometimes opens while driving. It sometimes takes many attempts to reclose it from the outside of car. It will not reclose using the electronic button on the door. The alert comes on on the dashboard and its extremely dangerous as luggage can fall out. This happened while highway driving last week, scary. Apparently after googling this, it is common issue. The tailgate is one big gate hinged at the top so stuff can fall out.

NHTSA ID

11646977

Incident

Mar 3, 2025

Coolant Reservoir Hose Blew out on my 2016 GL450 Mercedes Benz.

NHTSA ID

11565835

Incident

Dec 22, 2023

The contact owned a 2016 Mercedes-Benz GL450. The contact stated when he parked the vehicle and went into a business, he returned within 5 minutes and the vehicle was engulfed in flames. The fire department was already notified and arrived on the scene, then extinguished the fire with water. The police arrived on the scene; however, a report was not filed. The vehicle melted from the front bottom to the windshield. The vehicle was towed to the towing company. There were no injuries. No medical treatments were received on the scene or required. The manufacturer was notified of the failure. The vehicle was not diagnosed yet; however, the contact believes it was a total loss. The manufacturer was notified of the failure. The approximate failure mileage was 5,000.

NHTSA ID

11477187

Incident

Jul 26, 2022

Mileage

5,000 mi

Air Conditioner always make musty / moldy odor. Many forums says that is a common problem all across Mercedes models and it causes allergic reaction resulting in sneezing all the time when a/c is on. Problem is especially bad for my kids who have environmental allergy like mold/mildew. This horrible odor coming from a/c is due to mold/mildew forming on condenser. Please order a recall ASAP.

NHTSA ID

11472624

Incident

May 1, 2022

1. Transmission spontaneously disengaged park to allow the car to roll backwards 10 feet. No one was in the car at the time of the incident. I have a security system video of the incident. 2. Spontaneous runaway vehicle could have crashed children in the driveway or the street. 3. The dealer is not available to reproduce the problem. 4. No one performed any inspections at this time. 5. The vehicle did not present any warnings messages or other symptoms of the problem prior to the failure. I have a security system video that shows the vehicle parked and 20 minutes latter the vehicle spontaneously moving backwards a few feet and then stops. Please contact for a copy of this video.

NHTSA ID

11428599

Incident

Aug 10, 2021

WE PURCHASED THE CAR IN JULY 2019 AND IN ADDITION TO THE CAR HAVING WARRANTY UP TO 50,000 MILES, WE PURCHASED AN ADDITIONAL SERVICE/REPAIR PACKAGE FOR $1,800.00 RECENTLY WE NOTICED THAT WHEN WE FIRST START DRIVING THE CAR HAS A NOISE ON THE RIGHT SIDE, THE NOISE IS MOST NOTICEABLE WHEN APPLYING THE BRAKE AND WHEN RELEASING THE BRAKE. WE TOOK THE CAR TO MERCEDES BENZ OF VALENCIA AND TO SAY THAT THE SERVICE DEPARTMENT STAFF WAS UNWILLING TO HELP IS A GROSS UNDERSTATEMENT. THEY EVENTUALLY DID AGREE TO KEEP THE CAR GOVERNING AND TEST DRIVE IT IN THE MORNING, THEY CALLED THE FOLLOWING DAY ON DECEMBER 3RD AND TOLD US TO COME AND GET THE CAR. BILL THE SERVICE REPRESENTATIVE STATED THAT THEY HEARD THE NOISE WHEN APPLYING THE BRAKE AND SAID THERE IS NOTHING THEY CAN DO BECAUSE THE BRAKES ON THE CAR ARE NEW AND THAT THEY DO NOT KNOW WHAT COULD BE WRONG WITH THE CAR. WE ARE CONCERNED AND , WORRIED ABOUT OUR SAFETY, WE PURCHASED THE CAR AND THE ADDITIONAL REPAIR PACKAGE FOR PEACE OF MIND EXPECTING TO GET THE PROPER SERVICE TO ADDRESS ANY ISSUES BECAUSE THE CAR IS COVERED BY A 50,000 MILE WARRANTY AND WE PURCHASED ADDITIONAL SERVICE PACKAGE.

NHTSA ID

11288654

Incident

Dec 3, 2019

Mileage

40,058 mi

THE WINDSHIELD IS WEAK PRONE TO BREAK/CRACK EASILY. IN LESS THAN 3 YEARS 4 WINDSHIELDS HAVE BEEN REQUIRED. NOT NORMAL AND THIS IS POTENTIALLY DANGEROUS.

NHTSA ID

11098133

Incident

May 22, 2018

Mileage

3,500 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner as seen in the attached pictures. NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease). See the attached steering knuckle and wheel hub pictures for reference. NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Throttle Lift-Off Noise - Rear) LI33.30-P-056665 (Throttle Lift-Off Noise - Front) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced.

Complaint The customer requests deactivation of the N112/9 HERMES communication module Note: Deactivation of the HERMES control unit (N112/9) is not supported for gray-market vehicles. Cause Before deactivating the HERMES control unit (N112/9), it must be clarified by the legal department of the respective MPC whether and under what conditions deactivation may be carried out. If deactivation is not permissible under applicable law, the HERMES control unit (N112/9) must not be deactivated. Remedy Please inform the customer that, following deactivation, the vehicle will no longer be able to place an automatic emergency call, nor will the customer be able to place a manual emergency call. After deactivation, the Mercedes-Benz Digital Extras will also no longer be available. Please have the attached sample form checked by your market's legal department, adapted to local requirements if necessary, and approved. Furthermore, after informing the customer about the effects of deactivation, please have the workshop complete and sign the approved form together with the customer, and send it to the MPC via a TIPS case for audit-compliant documentation. Furthermore, the workshop must affix a sticker to the emergency call button cover on the overhead control panel and to the emergency call button itself. After affixing, pictures of the overhead control panel need to be attached to the TIPS case for audit-proof documentation. After deactivation, the HERMES control unit (N112/9) is in the "Out of Service" operating status, and the display "SOS NOT READY" appears in the Audio/COMAND system. This display message tells the customer that the emergency call function is not available. In detail, the following steps must be carried out 1. The workshop must inform the customer about the effects of deactivation (see above) 2. Legal review by the MPC Legal department to determine whether deactivation is permissible for the vehicle and provision of a market-specific customer form based on the examples (see "Example - Deactivation communication module HERMES customer declaration English V3.0.pdf") 3. Completion of the market-specific customer form by the workshop and obtaining the customer’s signature 4. Creation of a XSS ticket by the workshop for the MPC with the signed customer form attached 5. Written confirmation of legally reviewed and approved deactivation by the MPC in the TIPS case (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, point 1) 6. Creation of an XSS ticket for documentation of the SA code "09o" (zero nine oh) in the Vehicle Documentation System (see attachment How+to+request+adding+Code+09o+via+XSS+v2.pdf, steps 2–7) 7. Ordering of stickers (part number A9078172900), quantity: 2 8. Affixing of the sticker (part number A9078172900) to the cover of the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 9. Affixing of the sticker (part number A9078172900) to the emergency call button on the overhead control panel (see attachment HERMES-Deactivation_+pictures+of+sticker.png) 10. Taking photos of the applied stickers and attaching them to the TIPS case 11. After the XSS ticket has been successfully processed, the communication module must be deactivated using XENTRY: • Connect XENTRY Diagnosis • Access the HERMES control unit (N112/9) • "Adaptation" tab, menu item "Teach-in processes" -> "Deactivation" • Follow the instructions

Complaint After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the message "SOS - service not activated" appears on the instrument cluster. In addition, the following two conditions are also met: • HERMES (N112/9) control unit: event code B15CE00 is ACTIVE and STORED (A+S) • Vehicle Documentation System: For the HERMES control unit, the EID1, EID2, ICCID, IMEI, IMSI, TELNR fields in the "Identification/Serial number" column have the value "-" Cause Still under analysis Remedy Recommission the HERMES control unit (N112/9) with XENTRY Diagnosis 03/2026 and add-on 33399 installed or carry out the procedure with a newer version of XENTRY Diagnosis: XENTRY→ "N112/9 - Control unit for telematics services (HERMES)" -> "Adaptations" -> "Control unit commissioning" -> "Commissioning of previously installed control unit"

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).