2008 Mercedes-Benz ML350

See attached document for complaint

NHTSA ID

11583631

Incident

Feb 1, 2021

The contact owns a 2008 Mercedes-Benz ML350. The contact stated upon taking the vehicle to the dealer for servicing, he was informed that the VIN was included in NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The contact stated that the vehicle remained at the dealer for 2 months. The contact later received the recall notification. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue and advised the contact that parts were not available. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11484778

Incident

Sep 16, 2022

The contact owns a 2008 Mercedes-Benz ML350. The contact received notification of NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ID

11483473

Incident

May 9, 2022

The contact owns a 2008 Mercedes-Benz ML350. The contact received notification of NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11479841

Incident

May 9, 2022

The contact owns a 2008 Mercedes-Benz ML350. The contact received notification of NHTSA Campaign Number: 22V315000 (Service Brakes, Hydraulic) however, the part to do the recall repair was not yet available. The dealer was made aware of the issue. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11472787

Incident

Jul 7, 2022

The contact owns a 2008 Mercedes-Benz ML350. The contact stated while driving approximately 65 MPH, the steering wheel failed to respond as designed. The contact drove the vehicle safely off the road. The vehicle was taken to the local dealer to be diagnosed. The contact was made aware of a power steering rack leak. The vehicle was repaired; however, the failure recurred several times. The contact related the failure to NHTSA Campaign Number: 08V682000 (Steering). The manufacturer was notified of the failure. The approximate failure mileage was 38,000.

NHTSA ID

11458854

Incident

Feb 10, 2021

Mileage

38,000 mi

REAR LEFT AND RIGHT PASSENGER SEATBELT MECHANISMS (RETRACTING FUNCTION) ARE DEFECTIVE; BELTS DON'T WANT TO RETRACT BACK IN AFTER THEY HAVE BEEN PULLED OUT/USED

NHTSA ID

11378595

Incident

Aug 1, 2020

AFTER STARTING UP THE CAR AND TURNING ON THE SEAT HEATERS WE NOTICED A STRONG BURNING SMELL. WE HAD JUST ENTERED A SLIP ROAD AND MY WIFE (WHO WAS DRIVING) FELT A BURNING IN HER LOWER LEFT SIDE. NEXT THING... SHE WAS ON FIRE! HER WINTER COAT BUST INTO FLAMES AND AFTER PULLING OVER I GRABBED HER OUT OF THE DRIVERS SEAT AND ROLLED HER IN THE SNOW TO EXTINGUISH THE FIRE, WE WERE AMAZED THAT THE SEAT HAD A LARGE BURN HOLE THROUGH THE LEATHER AND THAT THERE WASN'T ANY SAFETY SHUT OFF FOR THE SEAT HEATER INITIATED BY THE VEHICLE. AFTER A DETAILED DESCRIPTION TO THE SERVICE MANAGER AT THE LOCAL MERCEDES DEALERSHIP OF WHAT HAD HAPPENED,WE WERE TOLD THAT A $2578 REPAIR WOULD FIX THE PROBLEM... WE WERE AMAZED AT HOW UNCARING THEY WERE AND THAT THERE WASN'T A RECALL ACTIVE FOR THIS DEFECTIVE WIRING PROBLEM. WE WERE RELIEVED THAT THIS DIDN'T CAUSE ANY FATALITIES TO US OR ANY OTHER PEOPLE THAT COULD HAVE BEEN AFFECTED IF WE WOULD HAVE BEEN ON A FREEWAY AT A HIGHER SPEED.

NHTSA ID

11310224

Incident

Feb 8, 2020

Mileage

167,000 mi

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Information: Please refer to this document in the warranty claim and, after completing diagnosis, select the damage code corresponding to the component part that caused the problem. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or multiple times, without an entrapment (anti‑pinch) event being detected. The concern may occur temporarily or repeatedly during normal closing operation. Cause The automatic reversing function of the panoramic roof is overly sensitive due to parameterization in combination with seal counter‑pressure. This condition can cause the roof to reverse even though no obstruction is present. Remedy Retrofit the vehicle to meet Cleanpoint status “Panoramic sliding sunroof glass panel reverses during closing without a pinch event.” The retrofit includes: • Hardware modification (installation of a cover rail / EPDM lip) • Corresponding software update for the panoramic roof control unit The prescribed retrofit steps must be performed in the specified sequence as outlined in this document. 1) Retrofit the EPDM lip onto the rear edge of the panoramic sliding roof panel: • Clean the underside of the rear edge of the sliding sunroof panel (marking, Figure 1) (e.g., isopropanol). • Subsequently install the cover rail on the underside of the sliding sunroof panel (Figure 2). - Distance from the cover rail to the rear edge of the sliding sunroof panel A = 5 mm - Distance from the cover rail to the right and left edges of the sliding sunroof panel B = 9 mm - Apply firm pressure by hand along the entire bonding surface of the COVER RAIL - The wider flange at the ends of the cover rail (see Figure 3) must point in the direction of travel 2) Submit an XSS Ticket with the following requests to add SA code O75 to the Vehicle Data Card • Enter code "O75" (Oscar 75) in Vehicle Documentation System (Vedok): • Add the following AO text to KG 78: AO code O75 added as specified in LI77.21-P-075806 (Version 7). 3) Install new software from the panoramic roof control unit (TSSR296, A98, PSD) and teach in the anti-pinch protection again: • Connect XENTRY Diagnosis. - always use the current XENTRY Diagnosis software release with all available add-ons. - Strict compliance with the operation steps in XENTRY Diagnosis is absolutely essential! - Ensure adequate power supply to the vehicle's on-board electrical system battery (greater than 12.5 V) using a battery charger. • Commission the panoramic roof control unit - To do this, select "A98 – control module 'panoramic sliding sunroof' → adaptation → commissioning → Commission the control unit." - Then follow user guidance in XENTRY Diagnosis. • Disconnect XENTRY Diagnosis.

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304