2016 Mercedes-Benz Sprinter 2500

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

The Office of Defects Investigation (ODI) analyzed complaint data provided by Daimler Vans USA, LLC (Daimler) as well as complaints submitted to ODI from consumers to identify incidents related to Rear Wheel Speed Sensors (RWSS) failures. ODI's analysis identified 6,710 incidents of RWSS failure (unique VINs) in MY 2012-2018 Mercedes- Benz and Freightliner Sprinter vehicles upfitted to campers or recreational vehicles (RVs) representing 81 percent of all Sprinter RWSS reports. Complaint and warranty analysis indicated that the majority of incidents (approximately 99%) were related to RWSS moisture intrusion condition in the Sprinter 3500 5-ton variant, which accounts for 98 percent of upfit campers, where moisture build-up and crystal dendrite formation develop in parked RVs and lead to sensor failures. According to the Daimler Information Request (IR) response, if the wheel speed information is detected as implausible by the Electronic Stability Program (ESP) control unit, the ESP system enters a failsafe mode where:-Driver torque requests are no longer accepted;-Cruise control, if used, would be deactivated; -The ESP/ABS system shuts off; and -Multiple warning lamps and messages advise the operator to take the vehicle to the workshop. While the majority of reports involved only ABS and/or ESP warning lights and messages on the instrument cluster due to faulty sensor signals triggering a failsafe mode, some reports cited intermittent sensor failures resulting in increased vehicle speed while in cruise control and degraded ABS or ESP. Degraded ESP functionality may impact driving stability of the 5-ton vehicle.On Feb 3, 2021, following discussion with ODI, Daimler submitted a Defect Information Report (DIR) to NHTSA describing a defect in the RWSS disabling the ESP control unit functions in approximately 48,667 MY 2012 through 2018 Mercedes-Benz and Freightliner Sprinter 3500 vehicles manufactured from Jan 4, 2012 through Oct 25, 2018 (Recall 21V-042). In its DIR, Daimler indicated that RWSS sensor failures are prevalent in camper vans due to sustained periods of non-use, during which time the moisture may not dry out, remaining inside the plastic housing package. If the moisture within the RWSS dries and the RWSS returns to normal operation, the failsafe mode and the warning lights will disappear at the next ignition cycle, but the sensor fault remains stored within the ESP control unit and can be accessed through a diagnostic evaluation. ODI will continue to monitor field experience in Sprinter non-RVs and Sprinter 2500 RVs 3-ton and 3.5-ton variants (approximately 626 vehicles).Daimler will notify owners of the recalled vehicles and advise them to take their vehicle to a Mercedes-Benz or Freightliner Sprinter dealer, who will replace the RWSS with a repackaged sensor with high robustness against moisture intrusion. Daimler began notifying dealers and owners in Feb 2021. This Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at NHTSA.gov under the following ID numbers:11352380 11351299 11350521 11348969 11342776 11342464 11341988 11341151 11340388 11338230 11337921 11331832 11331829 11331476 11331427 11331066 11328671 11325768 11325693 11322814 11322346 11320295 11319376 11317336 11311647 11310621 11308318 11254223 11253828 11252220 11196530 11194330 11164250 11145019 11141273 11139000 11138785 11124129 11094122 11394837 11390889 11390039 11389262 11387883 11387713 11386418 11383887 11383866 11382947 11377384 11376615 11376973 11375781 11375403 11374997 11374151 11373892 11373111 11366293 11365920 11365594 11365355 11365194 11364253 11364346 11363990 11363787 11362948 113629

The door latch and or roller failed which prevents the door from closing properly. Since the door does not close all the way, there is the risk that it opens while driving. This is a recurring issue I have on this vehicle and triggered a lemon-law buyback.

NHTSA ID

11757000

Incident

Aug 14, 2026

The power steering system lost it's fluid and pump is cavitating. It's available for inspection. The vehicles can be steered at the moment, but if it were to fail completely, it could cause loss of control at highway speeds. The problem is ongoing but hasn't been presented to a dealer or independent service center. No, the this hasn't been inspected. There were no warning lamps or messages or symptoms prior to failure. NOTE: there is an existing recall for 2015-2020 Sprinter vans for this issue, however upon contacting the dealership, the 2016 model doesn't currently fall under this recall.

NHTSA ID

11667211

Incident

May 31, 2025

The primary issue is the seal on the air conditioning unit, which is on top of the Sprinter van. Prior to purchasing it, we read multiple reviews that the seal breaks frequently and water pours into the cabin. It is a known defect and quite prevalent. Whenever we drive through rain and the seal is intact, we get drips of rain. When the seal needs to be replaced, gallons of water pour into the cabin. Replacing the seal costs thousands of dollars and we've replaced it a few times. We travel with buckets and a dozen bath towels in case we drive through rain. Seals for the air conditioning unit only last about a year before a new one is needed. Our local dealership is aware that this a widespread problem on Sprinters but Mercedes is refusing to to fix the issue. Secondly, the interior lights do not work. We've had them replaced and they quickly stop working. I'm not certain how prevalent this issue is in other Sprinters, but it is an issue that does not appear to have a long-time fix on our model.

NHTSA ID

11605186

Incident

Jul 22, 2024

Had 2 rims develop cracks causing loss of air pressure in tires. 1st occurred at approx. 45000 miles (2019), 2nd occurred at 110000 (2023). Both failures occurred to area of rim where welds to lock in center (with lug holes) on outer rim (where tire sits) are situated. Both failures manifested as small air leak then suddenly crack increases in size dramatically to where tire can only hold air for a few hours before deflating fully

NHTSA ID

11567265

Incident

Jan 3, 2024

The check engine light came on in the Sprinter van. There is a Hissing noise coming from the engine when accelerating. The Sprinter van loses speed when on the highway. The vehicle could not keep up with traffic on the road. The Mercedes Benz dealer, Ft. Mitchell, Kentucky has inspected the vehicle and stated that it has a defective intake manifold. This vehicle has 140,000 miles at this time. At this time the van has not been repaired, the cost is $3132.77

NHTSA ID

11532688

Incident

Jul 3, 2023

The contact owns a 2016 Mercedes-Benz Sprinter 2500. The contact received notification of NHTSA Campaign Number: 19V003000 (Air Bags), 19V004000 (Air Bags), and 20V663000 (Steering) however, the parts to do the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The dealer was made aware of the issue. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11526686

Incident

Jun 12, 2023

My 2016 Sprinter is suffering from a failing EGR valve that's causing intermittent power loss. The issue started after only 25000mi on the odometer. No errors are shown, nothing indicates malfunction. The problem is quite severe and presenting itself through random power loss. When accelerating the car will jerk and lose acceleration force suddenly. Driving uphill is the worst and producing constant jerking. Once moving at a good speed it's less notable but still present. The main safety concern is that the behavior is unpredictable and in situations where it's necessary to accelerate into a road with traffic, this can lead to a hazardous when the car doesn't accelerate as intended. In multiple occasions I was unable to properly speed up and get moving and thus blocking traffic behind me and forcing them to slow down or change lanes. The Mercedes dealer diagnosed a malfunctioning EGR valve on the edge of failing completely which would put the Sprinter in "limp home mode" which has limited power output to prevent further damage. Since this is a known issue and the EGR valves have been failing frequently with various Sprinter models, these should be recalled and replaced! Currently, it's not even possible to get this issue addressed. The EGR valves are back-ordered and not available for 6 MONTHS! That's 6 months of limping through traffic with the potential of the valve failing completely. Unacceptable!

NHTSA ID

11440452

Incident

Oct 28, 2021

There is a known issue and recall for wheel speed sensors on Mercedes Sprinter 3500 models. However, this same issue applied to 2500 models also. Along with other RV owners, I have just experienced this problem. I was in city traffic when all the sudden multiple warning lights came on: "ESP, visit workshop", "Brake force distribution, visit workshop", ABS warning light, ESP, warning light, collision prevention malfunction warning light, check engine light with fault code U0416. The presence of all these errors, beeping, red messages sounds extremely scary to any driver. The fact that it says brake force distribution isn't working properly suggests a hazardous condition that could lead to a crash if brakes are not working properly. Since this is being caused by a failing wheel speed sensor, these should all be replaced and the recall expanded to include other models like mine.

NHTSA ID

11440448

Incident

Nov 13, 2021

EGR Valve Diagnosis & Cleaning (and EGR Cooler Cleaning) – OM642, Sprinter 906/907 Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20‑N‑073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the desired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.

Acoustic Warning or message occurring when a closed sliding door is not recognized Complaint Customer may state the warning message or indicator accompanied by acoustic tone alerting the sliding door is ajar when the door is completely closed Cause There are several reasons that lead to the failure occurring: ‑ Mechanical damage through bending when loading and unloading ‑ Worn contact plates ‑‑> After detachment of silver plating, the coper plate is corroded ‑ Movement of sliding door/body when driving ‑‑> Contact pins do not always make contact with contact plate ‑‑> Central locking system fault message in instrument cluster Remedy In a problem case, replace contact switch for vehicles with +T50/+T55/+EL9 or contact plate with A4478201903 Check the fit of the sliding doors here and make any necessary adjustments as per AR72.16‑S‑1023E (447 /448) and AR72.16‑D‑1023TS (907/910). Further valid damage codes: 82326 Contact switch for central locking system on sliding door 82347 Contact plate for central locking system on sliding door 53196 K/Z contact plate for central locking system on sliding door 82645 Contact switch for sliding door

Unavailability of MB Apps Complaint A popup is seen on the HU with the message "data connection temporarily not available". Cause MB Apps is officially sundowned for all vehicles with NTG5 Head Unit Variant. Remedy No support available for NTG5 Head Unit Variants for MB App related topics.

Complaint While driving through muddy / sandy/ off road terrain "4Matic Currently Unavailable" message on the dash Cause This vehicle is not equipped with a fixed force distribution AWD, rather force is only applied to the front axle according to ESP calculations. As per GF28.00‑D‑ 9900A: "vehicles with 4MATIC all‑wheel system and variable force distribution, an electronically regulated multiplate clutch integrated into the transfer case provides for the torque distribution. If the multiplate clutch is open during normal driving operation, only the rear axle drives the vehicle. If the clutch is closed, the front axle comes into play." The message "All‑wheel drive temporarily unavailable" is not indicative of a malfunction but rather informs the driver that all‑wheel drive is currently not available due to the transfer case clutch overheating. This occurs when the vehicle is driven in such a way that maximum front axle torque is needed for an extended period, causing the clutch to get excessively hot. If the vehicle is being driven under heavy load conditions, like in deep sand or snow, the rear axle may slip while the front axle does not deliver power. The transfer case then attempts to distribute torque to correct the slip, but it is limited to a maximum of 1150 Nm to protect the front axle transmission. In extended heavy‑load scenarios, the multidisk clutch in the transfer case slips, increasing the temperature. If the temperature model detects a critical temperature of 240°C, the system protects itself by disconnecting until it cools down to around 160°C, after which the all‑wheel drive becomes available again and the warning message disappears.Vehicles can handle flat terrain easily, but steep slopes or situations where wheels slip might cause additional resistance, leading to the described protection events and message in the dash. Remedy Recommendation is to release the vehicle back to the client with an explanation that the vehicle is operating as designed. Please advise the client to limit vehicle acceleration in limited traction situations to avoid disabling of the 4Matic system ‑ please see "Notes on all‑wheel drive" provided in the operators manual.

ASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual. The service reminder may appear significantly earlier than anticipated even though no faults are stored and no malfunction is present in the vehicle. The remaining distance and remaining time continue to decrease normally until the service reminder is displayed. Cause This condition is not caused by a malfunction of ASSYST PLUS. ASSYST PLUS is a dynamic maintenance management system that continuously evaluates vehicle usage and opera-ting conditions to determine maintenance requirements. The starting maintenance interval specified by variant coding represents a maximum interval that may only be achieved under favorable operating conditions. Actual maintenance intervals may be significantly shorter depending on vehicle use. Vehicle operating conditions such as driving conditions, engine load, engine operating conditions, idling, short-trip operation, environmental influences, oil aging, and Diesel Particulate Filter (DPF) regeneration activity may reduce the maintenance interval from its starting value. These conditions may accelerate engine oil aging through increased soot loading, fuel dilution, moisture accumulation, and additional engine operating stress. As a result, the remaining distance and remaining time until the next service may be reduced from the starting maintenance interval. Remedy Do not replace any parts. A due service must be assumed if the maintenance data calculated by ASSYST PLUS indicates that service is required.

Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the de-sired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function. Remedy Remedy for Complaint A: Perform the following steps: 1. Disable the EGR Valve (Y27/17) by disconnecting the electrical connector. 2. Perform a test drive to check if the jolting/bucking issue resolves. 3. If the jolting/bucking is resolved, proceed to Remedy for Complaint B. 4. If jolting/bucking is still present, proceed with diagnosis to determine the root cause. Consider checking the follo-wing, but not limited to: •EGR system including the EGR Cooler, EGR Bypass Flap, EGR Temperature Sensor, and pipes for proper operati-on, excessive sooting and/or clogging, as well as EGR Bypass Flap vacuum element, switchover valve, and vacuum system. •Visually check the leak oil line or T-piece; reference LI07.00-N-059118.