2018 Peterbilt 567

The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE21-015) based on one Vehicle Owner Questionnaire (VOQ) and supporting fleet reports. The reports indicated that the subject quarter fenders were prone to cracking and/or separation.After a comprehensive review of the data related to the quarter fender failures on the subject vehicles, ODI did not identify the existence of a safety-related defect trend. Quarter fender failures resulted in a warranty claim rate less than one percent (<1%) of the total vehicle population. All separations, including those due to tread separations, road hazards, etc., accounted for less than point one percent (<0.1%) of the total vehicle population.ODI discovered that the minimum recommended gap between the top of the quarter fender and the bottom of the trailer was not known or being followed. The optional quarter fenders were supplied by Fontaine Spray Systems (FSS), who recommended a two inch (2) gap. ODI analyzed the claim data using a calculated gap. A calculated gap using the top of the quarter fender flap and assuming the trailer is level with the top of the fifth wheel hitch was necessary, as PACCAR doesn't know specifically what trailer a purchaser will couple to the tractor. It is safe to assume no trailers on the market extend below the upper fifth wheel plate, but many do provide additional clearance over the wheels where the quarter fenders are located. ODI determined that 94 percent of warranty claims and 84 percent of separations violated FSS' recommendation.ODI confirmed that the VOQ vehicle and the fleet report vehicles also violated FSS' recommended gap. In one fleet the gap was negative point three inches (-0.3).PACCAR has updated its vehicle specification process and issued a customer advisory notice to existing owners. In light of the low rate of reported failures and separations, further use of agency resources does not appear to be warranted. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves the right to take further action if warranted by the circumstances.

On May 1, 2020, the Office of Defects Investigation (ODI) opened PE20006 to investigate complaints of intermittent loss of power steering assist in Daimler Truck North America (DTNA), Volvo Trucks of North America (Volvo) and PACCAR vehicles equipped with a ZF/TRW (TRW) THP60 steering gear.  The investigation focused on 2010-2020 DTNA Freightliner Cascadia, M2 and WST; Volvo VN, VAH and VHD and PACCAR 337, 365, 389, 567, 579 model vehicles.Field reports and interviews with fleet drivers allege that high power steering fluid temperatures could result in internal seal and bearing failures causing pressure fluctuation, affecting left and right-hand turns.  The inability of the driver to steer the vehicle as intended can increase the risk of a crash and injury. ODI analyzed data provided by TRW, DTNA, Volvo, and PACCAR in response to individual information request letters.ODI found that most failures occurred within the first two years and/or 50,000 miles of service.  The claim rate decreased with time and miles in service and remained less than 0.5%. ODI normalized data from each of the manufacturers and determined that there was not a substantial difference in the failures.Additionally, TRW improved a seal in the steering gear in December 2015.Trucks built on or after 2016 (as 2017 and newer model years) show a decreasing trend of failures. In view of the overall low failure rate, the nature of early-life failure, and failure rate trending downward for model years 2017 and newer, this Preliminary Evaluation (PE) is closed.  The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

VEHICLE WOULD WANDER LEFT AND RIGHT WITHIN THE LANE ONCE UP TO ABOUT 40 MPH. SYMPTOMS FELT AS IF ALIGNMENT WAS OFF, OR AS IF TIRES WERE FOLLOWING A RUT IN THE PAVEMENT. ONCE VEHICLE WAS LOADED, STEERING WHEEL WOULD BE CLOCKED ABOUT 10-15 DEGREES TO THE LEFT WHILE VEHICLE TRACKED STRAIGHT. DRIVER WOULD HAVE TO CONTINUOUSLY APPLY CORRECTIVE INPUT TO THE STEERING WHEEL TO KEEP THE VEHICLE FROM DIVING LEFT AND RIGHT WHILE AT HIGHWAY SPEEDS. ISSUE WAS DETERMINED TO BE STEERING BOX FAILURE, DUE TO INCORRECT LENGTH OF ONE OF THE STEERING BOX MOUNTING BOLTS INSTALLED AT MANUFACTURING FACILITY. *TT *TR

NHTSA ID

11083705

Incident

Dec 26, 2017

Mileage

221 mi

105 chassis have been removed from the chassis list and unflagged in PRWS due to expiration of applicable warranty coverage. Total chassis population is 732.

The Condition, Chassis Affected, Service Action, Warranty, and Procedure sections have been updated to include the latest prognostics bulletin verbiage.

Troubleshooting procedures for 2.1m cab power windows are now available.

This recently published bulletin has been updated to include inspection procedures to assess if a hood is repairable.

Model 567 Hood Strut Support Structure -A new procedure is now available to install hood structure reinforcements on Model 567 and 567 BEV chassis, improving performance and durability.

The attached procedures document has been updated with more detail and explanations. This is not a stand-alone procedure. Cummins Quickserve troubleshooting will specify the use of these procedures while troubleshooting specific fault codes.