2004 Toyota Highlander Hybrid

On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.