1999 Chevrolet C10

IN A LETTER DATED APRIL 20, 2005, GM NOTIFIED NHTSA THAT IT HAD DECIDED THAT DEFECTS THAT RELATE TO MOTOR VEHICLE SAFETY EXIST IN CERTAIN MODEL YEAR (MY) 1999-2002 C/K 1500 SERIES (PBR PARKING BRAKE SYSTEM) AND MY 2001-2005 C/K 2500 AND 3500 SERIES (TRW PARKING BRAKE SYSTEM) PICKUPS WITH MANUAL TRANSMISSIONS.ACCORDING TO GM, SOME OF THESE VEHICLES MAY HAVE CONDITIONS THAT CAUSE THE FRICTION LININGS TO WEAR TO AN EXTENT WHERE THE PARKING BRAKE CAN BECOME INEFFECTIVE IN IMMOBILIZING A PARKED VEHICLE.GM'S ACTION COVERS AN ESTIMATED TOTAL OF 142,585 VEHICLES.DEALERS WILL INSTALL A LOW-FORCE SPRING CLIP RETAINER FOR VEHICLES EQUIPPED WITH THE PBR PARKING BRAKE SYSTEM AND INSTALL A REDESIGNED PARKING BRAKE CABLE ASSEMBLY ON VEHICLES EQUIPPED WITH THE TRW PARKING BRAKE SYSTEM. A TOTAL OF 58 NON-DUPLICATIVE COMPLAINTS WERE RECEIVED BY ODI AND GM CONCERNING THE APPROXIMATELY 59,000 MY 1999-2002 C/K 1500 SERIES PICKUP TRUCKS WITH THE PBR PARKING BRAKE SYSTEM.THESE INCLUDED 22 ALLEGED ROLLAWAY INCIDENTS, RESULTING IN A RATE OF 38.5 ROLLAWAY INCIDENTS PER 100,000 VEHICLES.ODI IS AWARE OF 24 COMPLAINTS REGARDING THE MY 2001-2005 C/K 2500 AND 3500 SERIES MANUAL TRANSMISSION TRUCKS RECALLED BY GM, INCLUDING 5 ALLEGING ROLLAWAY INCIDENTS.THOUGH THE CONDITIONS DESCRIBED IN GM'S LETTER ARE ALSO PRESENT IN THE C/K TRUCKS WITH AUTOMATIC TRANSMISSIONS, THE ROLLAWAY RATE IN THOSE VEHICLES WAS SIMILAR TO THOSE OBSERVED IN PEER VEHICLES STUDIED BY ODI IN THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED. FOR ADDITIONAL INFORMATION, SEE THE ATTACHED CLOSING REPORT.

ODI OPENED PE03-057 TO ASSESS PARKING BRAKE INEFFECTIVENESS IN THE SUBJECT VEHICLES.THESE VEHICLES ARE EQUIPPED WITH FOUR WHEEL DISC BRAKES THAT INCORPORATE A SINGLE-SHOE DRUM-IN-HAT PARKING BRAKE INDEPENDENT OF THE SERVICE BRAKES.COMPLAINT AND WARRANTY DATA INDICATE THAT THE PARKING BRAKE LININGS TEND TO WEAR OUT EARLY IN THE LIFE OF THE VEHICLE (AT AN AVERAGE OF 24 MONTHS IN SERVICE), REDUCING THE PARKING BRAKE SYSTEM'S TORQUE BELOW THAT NEEDED TO IMMOBILIZE THE VEHICLE.GM HAS ATTRIBUTED THIS ACCELERATED WEAR TO FOREIGN MATERIAL INTRUSION AND A FAILURE OF THE BRAKE SHOE TO PROPERLY SELF-CENTER WITHIN ITS BRAKE DRUM.EFFECTIVE WITH THE START OF MY 2003 PRODUCTION, A NEWER REDUCED FORCE HOLD-DOWN CLIP WAS INTRODUCED TO FACILITATE BRAKE SHOE DISENGAGEMENT FROM THE DRUM SURFACE.THIS PART IS ALSO AVAILABLE AT THE SERVICE LEVEL FOR THE MY 1999-2002 VEHICLES.GM HAS INDICATED THAT THE PAKING BRAKE IS INTENDED TO OPERATE IN CONJUNCTION WITH THE TRANSMISSION TO IMMOBILZE PARKED VEHICLES, AND THAT IN MANY CASES, ACCELERATED PARKING BRAKE LINING WEAR IS CAUSED BY ROUGH USE, VEHICLE MODIFICATIONS, AND DRIVING WITH THE PARKING ENGAGED. ODI HAS UPGRADED THE PRELIMINARY EVALUATION TO AN ENGINEERING ANALYSIS TO GATHER FURTHER INFORMATION CONCERNING PARKING BRAKE USAGE FACTORS AND THE CIRCUMSTANCES SURROUNDING THE SEVENTEEN REPORTED VEHICLE CRASHES.

DT: THE CONTACT STATED ABS BRAKES WENT OUT 2 YEARS AGO. THE ABS LIGHT CAME ON TO ALERT HIM THERE WAS A PROBLEM WITH THE BRAKES PRIOR TO TAKING OUT THE FUSE. THE SERVICE MANAGER SAID IT WOULD COST $900.00 TO FIX IT OR TO TAKE OUT THE FUSE. HE SAW IN THE NEWSPAPER SIX MONTHS AGO ABOUT THE PROBLEMS GMC WAS HAVING WITH THE ABS BRAKES. *AK

NHTSA ID

10132591

Incident

Aug 12, 2005

Mileage

50,000 mi

WHILE DRIVING AT ANY SPEED IN RAINY WEATHER FRONT WINDSHIELD WIPERS SHUT OFF INTERMITTENTLY. DEALERSHIP WAS NOTIFIED, BUT DID NOT RESOLVE THE PROBLEM. *AK

NHTSA ID

10117252

Incident

Feb 16, 2005

Mileage

105,000 mi

SERIAL NUMBERS DD85338-3AG DD82338-3DG BRIDGESTONE IGNORED MY REPORT TO THEM.M *AK (TIRESIZE: LT265-75R-)

NHTSA ID

751996

Incident

Jul 30, 2001

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

Vehicle Recalls

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.