2012 Ford F-53

WHILE DRIVING ON THE HIGHWAY I NOTICED A SUDDEN AND DISTINCT DETERIORATION IN HANDLING, SO SEVERE THAT IN CROSSWINDS OR WHEN BEING PASSED BY A SEMI-TRAILER IT WAS DIFFICULT TO MAINTAIN CONTROL AND STAY IN MY LANE OR ON THE ROAD. WHEN I INSPECTED THE VEHICLE I FOUND THAT THE PASSENGER SIDE REAR ANTI-SWAY BAR BUSHING BRACKET, MOUNTING BOLTS, AND NUTS WERE ALL MISSING, EFFECTIVELY DISCONNECTING THE REAR ANTI-SWAY BAR AND CAUSING DANGEROUS BODY ROLL. IN TRYING TO DETERMINE HOW THIS OCCURRED I FOUND A THREAD ON THE WWW.IRV2.COM FORUM INDICATING THIS IS A COMMON PROBLEM WITH ALL YEAR MODELS OF THE FORD F53 MOTORHOME CHASSIS.

NHTSA ID

11191615

Incident

Feb 17, 2019

Mileage

22,000 mi

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.

On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.