2008 Ford F-53

TL* THE CONTACT OWNS A 2010 NEWMARK CAYON STAR RV. THE VEHICLE WAS EQUIPPED WITH A 2008 FORD F-53 CHASSIS. THE CONTACT STATED WHILE DRIVING APPROXIMATELY 35 MPH, THE BRAKE PEDAL TRAVELED TO THE FLOOR UPON ENGAGING. THE VEHICLE FAILED TO SLOW DOWN UNTIL AFTER DOWN SHIFTING AND APPLYING THE EMERGENCY BRAKE. THE VEHICLE WAS TOWED TO AN AUTHORIZED DEALER, WHO REPLACED THAT THE FOUR CALIPERS AND ROTORS, FIVE BRAKE LINES. IN ADDITION, THE FRONT AND REAR BRAKE PADS WERE REPLACED. THE MANUFACTURER WAS NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 9,960. UPDATED 09/16/14*LJ THE CONSUMER STATED THE CALIPERS WERE STICKING IN APPLIED POSITION RESULTING IN ABNORMAL HEAT GENERATION AT THE WHEELEND. THIS CAUSED BRAKE DRAG. THIS CAUSED 2 BRAKE LINES TO RUPTURE. UPDATED 1/16/15 *JS

NHTSA ID

10619352

Incident

Jun 4, 2014

Mileage

9,960 mi

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

When performing any transmission fluid changes or topoffs involving MERCON SP, MERCON LV has replaced all versions of MERCON SP and can be used going forward. Mixing MERCON LV and MERCON SP in the same transmission is acceptable. After 30-Jun-2023, MERCON SP ATF will no longer be manufactured and will only be available until inventory depletes.

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

Various vehicles equipped with a 4.6L, 5.4L, 6.8L modular 3 valve engine built on or before 8-Jan-2016 may exhibit symptoms that may include upper end engine noise, rough running, misfire and/or engine damage. If diagnosis leads to only camshaft/camshaft roller follower(s) requiring replacement, replace all of the camshaft roller followers on both banks/cylinder heads with part number 3L3Z-6564-A, not just the faulty roller follower(s). When replacing the camshaft roller followers, refer to Workshop Manual (WSM), Section 303-01.

Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab  select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab  select Dealer Installed Accessory or Accessory Installation.