2013 Ford F-53

Brakelines are rusted and I am afraid they will rust through and cause brake failure. Looked at a 2017 model and the brakelines look to be coated to prevent this from happening.

NHTSA ID

11493183

Incident

Nov 1, 2022

HEADLIGHTS WILL ONLY ILLUMINATE THE HIGHWAY A SHORT DISTANCE AHEAD (50-60 FT) OF THE VEHICLE. CANNOT DRIVE AT NIGHT. ALSO, THE BRAKES TO NOT SEEM TO BE ADEQUATE. *DT CONSUMER SOLD THE VEHICLE.*JB

NHTSA ID

11101328

Incident

Jun 10, 2014

Mileage

300 mi

TL* THE CONTACT OWNS A 2013 FORD F-53. THE CONTACT STATED THAT THE FRONT WINDSHIELD FIBER GLASS WAS SEPARATING FROM THE MOTOR HOME. UPON INSPECTION, THE CONTACT NOTICED THAT THE GLUE BETWEEN THE FIBER GLASS AND METAL WAS PEELING AND CAUSED THE SEPARATION. THE VEHICLE WAS NOT TAKEN TO A DEALER OR INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING OR REPAIRS. THE MANUFACTURER INFORMED THE CONTACT THAT THE WARRANTY HAD EXPIRED AND NO FURTHER ASSISTANCE WAS OFFERED. THE FAILURE MILEAGE WAS 35,000.

NHTSA ID

11099011

Incident

Aug 1, 2017

Mileage

35,000 mi

MOTOR HOME WAS PURCHASED NEW IN MAY OF 2013. WHILE DRIVING THIS SUMMER I NOTICED MORE SWAY/ROLL THAN USUAL, SO I RESEARCHED 'FORD F53 CHASSIS- HANDLING ISSUES'. I FOUND THAT A LOT OF OWNERS REPORTED PROBLEMS WITH SOME OF THE BRACKETS ON THE REAR SWAY BARS. SOME HAD LOOSE OR MISSING BOLTS, LOOSE OR BENT OR MISSING BRACKETS ( EITHER SIDE). I WANTED TO SEE IF THIS COULD BE THE ISSUE I WAS HAVING WITH THE NOTICEABLE INCREASE SWAY/ROLL, SO I CRAWLED UNDER RIG TO INSPECT THE BRACKETS ON JULY 3RD, 2017. I FOUND THE SWAY BAR BRACKET ON DRIVERS SIDE, WAS BENT, BROKEN AND HANGING DOWN. THE UPPER BOLT WAS TIGHT AND HOLDING THE OTHER PIECE OF THE BRACKET (ABOUT 1" SQUARE) THE LOWER BOLT WAS LOOSE AND HOLDING THE REST OF THE BENT/BROKEN BRACKET AND THE POLY BUSHING HAD SLID 2"-3" FROM IT'S INSTALLED POSITION. I DON'T KNOW WHEN THE BRACKET CAME LOOSE/BROKE BUT I KNEW THAT IT WOULD NOT BE SAFE TO CONTINUE DRIVING THE MH IN THIS STATE, SO I ORDERED THE NEW BRACKET FROM A NEARBY FORD PARTS SUPPLIER AND INSTALLED IT MYSELF. I WILL TRY TO ATTACH PICS OF BROKEN BRACKET AS FIRST DISCOVERED AND PIC OF REPLACEMENT BRACKET RECEIPT. THE FORUM THAT I LEARNED OF THIS PROBLEM WAS 'IRV2' AND HAVE FOUND THAT IT HAS BEEN A ISSUE ON ALL MAKES, MODELS AND YEARS WITH THE FORD F53 CHASSIS. AND THAT IT NEEDS TO BE BROUGHT TO NHTSA ATTENTION. AS A LOT OF OWNERS JUST 'FIX' THE PROBLEM THEMSELVES UNLESS VEHICLE IS UNDER WARRANTY AND THE PROBLEM NEVER GETS REPORTED.

NHTSA ID

11021463

Incident

Jul 3, 2017

Mileage

17,150 mi

THE REAR STABILIZER BAR (ALSO CALLED AN ANTI-SWAY BAR) BRACKET BOLTS CAME LOOSE. THE UNIT HAD UNDER 5,000 MILES ON IT. I TORQUED THE BOLTS AND THEY CAME LOOSE AGAIN AFTER ANOTHER FEW THOUSAND MILES. I WAS A CERTIFIED ASE TECHNICIAN AND ALSO AN AUTOMOTIVE INSTRUCTOR FOR 35 YEARS (RETIRED) AND EVENTUALLY FIXED THE PROBLEM WITH LOCK TIGHT ON THE BOLT THREADS. I HAVE HEARD OF MANY OTHERS WITH THE SAME ISSUES ON THE F-53 RV CHASSIS. BECAUSE THE BOLTS WERE JUST LOOSE NO DRIVING ISSUES WERE NOTICED. MANY HAVE REPORTED TO ME ABOUT MISSING BOLTS AND BRACKETS. WHEN THIS HAPPENS A LOSS OF SWAY CONTROL WILL OCCUR. SINCE ONLY BOLTS WERE LOOSE I DON'T HAVE PICTURES.

NHTSA ID

11021254

Incident

Jun 25, 2014

2014 FOREST RIVER FR3. CONSUMER REQUESTS REIMBURSEMENT FOR ELECTRIC DOUBLE STEP RECALL NOTICE REPAIRS. *LD UPDATED 07/10/2017*JS

NHTSA ID

11002229

Incident

Nov 24, 2014

THE HEADLIGHTS ON THE MOTOR HOME ARE INADEQUATE FOR NIGHT DRIVING. THEY ARE DANGEROUS CAUSING THE NEED TO USE THE HIGH BEAMS WHICH IS NOT IDEAL. THE DAYTIME DRIVING LIGHTS ON MY CAR DO A BETTER JOB. THE ARE SOME SORT OF CHEAP AFTERMARKET LIGHTS THAT CAN'T BE DOT APPROVED. *DT CONSUMER NO LONGER HAS THE VEHICLE.*JB

NHTSA ID

10789718

Incident

Nov 7, 2015

Mileage

20,000 mi

TL* THE CONTACT OWNS A 2014 WINNEBAGO ITASCA SUNSTAR RV EQUIPPED WITH A 2013 FORD F-53 SD CHASSIS. WHILE DRIVING DOWN AN INCLINE AT APPROXIMATELY 35 MPH, THE BRAKE PEDAL WAS ENGAGED AND THE VEHICLE FAILED TO SLOW DOWN. THE TOW HAUL CONTROL BUTTON WAS ACTIVATED AND THE VEHICLE CAME TO A COMPLETE STOP. THE VEHICLE CONTINUED IN OPERATION. THE FAILURE RECURRED INTERMITTENTLY. THE VEHICLE WAS TAKEN TO THREE DIFFERENT DEALERS FOR DIAGNOSTIC TESTING, BUT THE MECHANICS WERE UNABLE TO DUPLICATE OR LOCATE THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 850. UPDATED 09/03/15*LJ UPDATED 10/17/2017*CN

NHTSA ID

10721785

Incident

Oct 17, 2014

Mileage

850 mi

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.