2026 Mazda CX-50

On several occasions, moving the gear selector from Reverse to Drive, the transmission has failed to engage Drive, with the dashboard displaying "D" and the vehicle moving in reverse upon throttle application. Fortunately, objects, pets or pedestrians were not present behind the vehicle during the occurrences. The dealership was unable to duplicate the condition and found no software updates or other notices from Mazda addressing the issue.

NHTSA ID

11754509

Incident

May 15, 2026

I parked this hybrid rental vehicle on a steep street facing uphill and remained in the car with it on for about 15 to 30 minutes. When I put the vehicle back in Drive, released the brake pedal, and pressed the gas pedal to drive away, the car quickly free-rolled backwards. There was no throttle response, and I had to quickly brake to stop the car from its quick backwards descent. Multiple attempts to correct the issue, including various combinations of placing the car back in Park and back in Drive, engaging the electronic parking brake, etc., had no effect. There was no throttle response at all when in Drive, and no ability to control the free-roll of the car after pressing the gas pedal when in Drive without braking. I even tried placing the car in Reverse, and this allowed me to go backwards at a controlled speed instead of free-rolling, but Drive only initiated an uncontrollable backward free-roll. Note that the hybrid vehicle was on, but the engine did not sound like it was running, and I believe it was in electric mode while experiencing this issue. There were no warning lamps, messages, or other symptoms of problems prior to or during the issue. Over the course of these various attempts I rolled backwards several car lengths. Had there been a vehicle or person behind me, there would have been an accident. I eventually placed the car in Park and turned it off and left it there. When I returned about 2 hours later the vehicle behaved as normal, and the issue was never experienced again while I had the rental car. Since this was a Budget rental car, they would need to be contacted about any availability for inspection. I did not report the issue to Budget or to Mazda. This issue concerned me enough to report it directly to NHTSA.

NHTSA ID

11752755

Incident

Jul 16, 2026

The contact's daughter owns a 2026 Mazda CX-50. The contact stated that while his daughter was driving 40 MPH and decelerating to turn into a parking lot, the front passenger’s side wheel detached and fell in underneath the vehicle. The vehicle was towed to a tow yard and was then towed to the dealer. The dealer stated that the failure was due to a crash and informed the owner that the repair was not covered under warranty; however, the contact stated that a Police Officer confirmed that there was no damage to the curb or in the vicinity of the vehicle during the failure. No diagnostic information was available. Upon inspection by an insurance adjuster, it was determined that the repair would be covered by the insurance company and would be performed using aftermarket parts. The parts were unavailable, and the vehicle was not repaired. The manufacturer was notified of the failure and assisted in locating a dealer. The failure mileage was approximately 3,506.

NHTSA ID

11751784

Incident

Jul 12, 2026

Mileage

3,506 mi

Was braking with traffic and all of a sudden the emergency braking kicked on and brought the car to a stop from about 40 miles per hour with no immediate threat of collision. Brakes were being applied manually and had plenty of room infront of the vehicle and traffic was not stopped. Nearly caused the vehicle behind to collide into me. Very uncomfortable whiplash feeling experienced and my unsecured belongings in my car went flying.

NHTSA ID

11750218

Incident

Jul 14, 2026

Component: Air Bags – Knee Airbag / Trim Panel During a collision, on July 3rd with the Mazda CX‑50, the knee airbag deployed and a hard plastic trim panel from the lower dashboard was forcibly ejected. This panel struck my knee and caused a laceration across my kneecap. The injury was not caused by the crash itself but directly by the detached interior component. The trim panel appears to be part of the knee‑airbag assembly and should not detach with enough force or sharpness to cause bodily harm. I experience pain, discomfort, and ongoing issues due to the injury with tingling down my left leg when I get up to walk. I am concerned this represents a design or manufacturing defect in the knee‑airbag trim panel or its breakaway mechanism. Photos of the deployed airbag, the detached part, and the injury are available.

NHTSA ID

11749114

Incident

Jul 3, 2026

This report concerns the design of the front seat belt reminder system, which I believe creates a safety hazard. The audible warning begins the instant the engine starts — while the vehicle is stationary in Park — is very loud, and repeats indefinitely until the belt is latched. Federal Standard No. 208 requires only a short warning (up to 8 seconds); this immediate, persistent chime is a voluntary design choice. Other manufacturers (e.g., Honda) meet the same standard while chiming only once the vehicle is in motion, which is sufficient and far less intrusive. The safety problem: because the warning is so aggravating, owners are defeating their own seat belt systems. Owners across the Mazda lineup — CX-5, CX-30, CX-50, CX-90, Mazda3, and Mazda6 — publicly document this on owner forums ([XXX], [XXX], [XXX], [XXX], [XXX], [XXX]) and in TikTok and YouTube tutorials. Common methods include cutting or de-pinning the buckle-latch wire so the car always reads as belted, and installing uncertified seat belt extenders or dummy buckles. The buckle-latch signal feeds the airbag/SRS control module and affects airbag and pretensioner deployment, so these workarounds degrade crash protection. NHTSA's own research notes that reminders annoying enough to be circumvented reduce seat belt use. Mazda has acknowledged the excessive chime volume in Technical Service Bulletin 09-002-24. The system operates as designed — the design itself is the hazard. Symptom: continuous chime and belt warning light at startup while in Park; vehicle available for inspection on request. I request that NHTSA review whether this reminder design induces unsafe circumvention and should be revised. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11748544

Incident

Jul 4, 2026

I was backing out of a parking spot in a parking lot that backed up to a 2 lane highway. I placed the car in Reverse and then put the car in Drive, so that I could exit the parking lot to a side road. When I placed the car in Drive and pressed gas, the car went into Reverse (towards the 2 lane highway behind me). I placed the car in park, then back to Drive, it went in Reverse again. We were now in the 2 lane highway with oncoming traffic swerving to avoid us. We decided to put the car in park and turn off the car. Then, we restarted and place the car in Drive. It went into drive and we moved forward into the parking lot, off the highway and then we could exit the parking lot and drive home.

NHTSA ID

11748332

Incident

Jul 4, 2026

At approximately 2,900 miles, during the first oil change/service, the factory-installed spin-on oil filter could not be removed normally. The oil filter required approximately one hour of removal effort and would not spin off in a normal manner. When the filter was finally removed, the oil filter threaded adapter/union came out of the engine-side oil filter housing while still seized inside the oil filter. The adapter threads showed visible damage, including flattened, galled, and torn thread areas. The oil filter was seized tightly enough to the adapter that the oil filter had to be cut away from the adapter to separate the parts. The adapter was removed from the filter without adding further damage. The damaged adapter threads were cleaned/chased only as a temporary repair because the vehicle was needed for work and parts were not immediately available over the weekend. A new correct replacement oil filter was test-fitted to the adapter. It threaded fully onto the adapter by hand but had slight binding in the previously damaged thread area. The filter was installed, the engine was started, and the assembly was checked for leaks. No leak was observed during the temporary service check. However, the adapter remains damaged and should be replaced. This appears to be a manufacturing, assembly, or original filter installation issue, because the vehicle had only approximately 2,900 miles and the factory-installed oil filter was seized to the oil filter threaded union. The filter should not be seized to the adapter at this mileage, and the threaded adapter should not be pulled out of the engine-side housing during normal oil filter removal. The concern is that a damaged or improperly threaded oil filter adapter could cause oil filter sealing failure, oil leakage, loss of engine oil pressure, engine damage, or an oil leak onto the roadway. The damaged threaded oil filter adapter/union should be documented as a factory/dealer assembly defect.

NHTSA ID

11745430

Incident

Jun 19, 2026

This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-063/24 09/06/24 DESCRIPTION The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction.

COMPLIANCE WITH NEW YORK STATE GENERAL BUSINESS LAW §399‑CCCCC (CONNECTED VEHICLE SERVICE; DOMESTIC VIOLENCE VICTIMS) DESCRIPTION This Service Information is issued in accordance with New York State General Business Law §399􀀀CCCCC (Connected Vehicle Service; Domestic Violence Victims). This regulation is intended to protect victims of domestic violence by allowing them to request the termination of third-party access (including access by an alleged abuser) to connected vehicle services, such as vehicle location tracking and remote control functions. To support this requirement, this Service Information enables confirmation of whether a vehicle is subject to connected vehicle services by referring to the SUBJECT VIN & PRODUCTION DATE RANGE, and provides guidance on the procedure to terminate such services when a customer requests the removal of third-party access for an applicable vehicle. Effective July 1, 2026, if a customer requests action under this regulation, a CMU/CDC software update must be performed to enable appropriate control of connected vehicle service access. If no request is made by the customer, the CMU/CDC software update is not required. REPAIR PROCEDURE 1. Confirm that the customer has requested deactivation of connected services in accordance with New York State General Business Law related action. 2. Perform the CMU/CDC software update according to the procedures outlined in the appropriate TSB shown in the table below:

This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out

UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-001/26 01/08/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA01_***** or 7230C2A-NA01_*****, this TSB is not applicable. Version 7230C1A-NA01_10022 enables termination of connected services at customer request: Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. ○ • The list on the center display may appear distorted, giving a double image. • The system may reboot when the ignition is turned on. However, the camera images on the center display are not affected, and the back camera is usable. • The voice recognition function does not start. • Apple CarPlay® may fail to connect while driving on the highway. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA01_10022/7230C2A-NA01_10014 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.

DESCRIPTION Some vehicles may exhibit a clicking, popping, tapping or knocking noise from the front end when turning left or right and accelerating. NOTE: The noise could occur at different steering wheel angles or power levels. Due to the insulating properties of the suspension and chassis, it can be difficult to determine which driveshaft is at fault by listening from inside the vehicle. See the attached video for an example of an outer CV joint clicking. These noises may be caused by the outer ball joint cage machining being out of specification. To eliminate this concern, tighter quality controls have been implemented to ensure proper machining of the cage window. NOTE: The part number for the improved part has not been changed. The current parts inventory is after the countermeasure production date implementation.

This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.