2007 Mercedes-Benz CLS550

The fuel tank has a leak from a defect in the plastic, and my local Mercedes dealership is unwilling to honor the Warranty Coverage Extension that covered fuel tank components to replace the fuel tank.

NHTSA ID

11693552

Incident

Oct 1, 2025

Drained Battery everyday.

NHTSA ID

11484706

Incident

Sep 1, 2020

WHILE DRIVING THE VECHILE LOWERED AND I NOTICED A PUDDLE WHILE IDLE

NHTSA ID

11390873

Incident

Jan 29, 2021

Mileage

118,000 mi

DEFECTIVE INTERNAL SPEED SENSOR DOES NOT SEND SIGNAL TO TCM(TRANSMISSION CONTROL MODULE) CAUSING LOSS OF POWER WHILE MOVING. THE ONLY WAY TO GET CAR GOING AGAIN IS TO SHUT OFF CAR AND RESTART HOPING IT WILL RESET. IF THIS WERE TO HAPPEN IN CONSTRUCTION ZONE WITH NOWHERE TO PULL OVER, MAY BE DEADLY.

NHTSA ID

11299919

Incident

Jan 1, 2020

Mileage

44,600 mi

DRIVING HIGHWAY SPEEDS AND SUDDENLY VEHICLE JERKED AND LOSSES ALL POWER. ENGINE REVS BUT DOESN'T MOVE. THIS CAN BE A VERY DANGEROUS SITUATION. TRANSMISSION WENT INTO 'LIMP' MODE AND CHECK ENGINE LIGHT LIT. MANY OTHER MERCEDES OWNERS REPORTING SAME PROBLEM WITH THE 722.9 TRANSMISSION VALVEBODY, CONDUCTOR PLATE, AND/OR TCM. THIS SHOULD BE INVESTIGATED AS COUNTLESS OTHER PEOPLE ARE REPORTING THIS SAME ISSUE FOR SEVERAL YEARS NOW.

NHTSA ID

11163610

Incident

Dec 26, 2018

Mileage

116,000 mi

I AM REFERENCING ACTION # PE12001. AFTER EACH OF MY LAST TWO FUEL FILLLINGS, THE CAR IS EMITTING A VERY STRONG SMELL OF GASOLINE FROM THE BACK SEAT & TRUNK COMPARTMENT. I PARK MY CAR IN MY GARAGE AND THE SMELL IS STRONG ENOUGH THAT I CAN SMELL IT IN MY HOME. I AM EXTREMELY FEARFUL THAT THERE WILL BE A FIRE. I DO NOT DESIRE TO PARK MY CAR OUTSIDE, BUT I BELIEVE THE CAR IS UNSAFE TO KEEP IN GARAGE. I HAVE LOST CONFIDENCE IN MY CAR FEARING THAT EVEN DRIVING IT AROUND TOWN COULD POSE A DANGER TO ME AND MY PASSENGERS.

NHTSA ID

11024177

Incident

Jul 28, 2017

Mileage

86,000 mi

NOTE THAT THE VEHICLE ON HAS 43,733 MILES - CABIN INTERIOR STRONG LIVE FUEL FUMES - CONSTANT GAS FUMES ON THE INSIDE OF THE CAR CABIN. NOTE THAT THE CAR WAS STATIONARY AT MY RESIDENCE PARKING. I DID NOT KNOW WHERE WERE THE FUMES COMING FROM AT THE TIME. GOT A HEADACHE JUST FOR THE MOMENT I WAS TRYING TO DETERMINED WHERE WERE THE FUMES COMING FROM. THIS IS CURRENTLY FOR ALL DRIVERS AND OWNERS A VERY HAZARDOUS DANGEROUS CONDITION TO ALL EXTREMES, VERY HIGH RISK FROM IGNITION FROM STATIC OR ELECTRICAL, DUE TO WIRE HARDNESS IN THE AREA. VEHICLE WAS TOWED AND TOOK IT TO MERCEDES BENZ DEALER AND FOUND THE FOLLOWING: LEAKAGE IN FUEL SYSTEM. REPLACED FUEL TANK FUEL TANK DRAIN/FILL OBSERVED ACCIDENT PREVENTION REGULATION "12 WL08" FUEL TANK AND FUEL FOR STORAGEBRING OBSERVE ACCIDENT PREVENTION REGULATION "12 WL08" PERFORMED BY MERCEDES-BENZ OF NEW ORLEANS. FUEL TANK LEAKING IN THE INTERIOR WAS FOUND / WAS DRAINED & REFILLED AND FUEL TANK REPLACED. THIS WAS COVER UNDER A NEW SETTLEMENT WITH MERCEDES BENZ AND NHTSA. I THINK THAT THIS SHOULD HAVE BEEN A RECALL WHEN IT RELATES TO SAFETY FACTORS.

NHTSA ID

10986233

Incident

May 5, 2017

Mileage

43,733 mi

MY HUSBAND AND I PURCHASED THE 2007 CLS550 ABOUT SEPTEMBER 2015. WE NOTICED WHEN FILLING THE VEHICLE WITH GAS, WE WOULD HAVE GAS FUMES IN THE VEHICLE SPECIFICALLY ON THE PASSENGER SIDE REAR INSIDE AND OUTSIDE. THE FUMES WERE LIGHT AND WOULD DISSIPATE ONCE THE VEHICLE WAS DRIVEN TO REDUCE THE AMOUNT OF GAS IN THE TANK TO ABOUT THREE-QUARTERS TANK. LAST WEEK WE FILLED THE TANK AND THE SMALL IS NOW STRONGER AND HAS YET TO DISSIPATE ALTHOUGH WE HAVE A QUARTER TANK OF GAS REMAINING. I CHECKED FOR ANY RECALLS ON THIS SINCE WE HAVE NO KNOWLEDGE OF THE VEHICLE HAVING BEEN IN ANY ACCIDENTS, BUT FIND WE DO NOT. THIS ONLINE SEARCH DID NOT REVEAL ANY RECALLS FOR THE GAS FUMES, BUT I NOTED THERE ARE MULTIPLE COMPLAINTS ABOUT THE SAME PROBLEM FOR THIS YEAR, MAKE AND MODEL OF VEHICLE. HAVE ANY PEOPLE DIED FROM THIS, ANY FIRES, ACCIDENTS AS A RESULT? WE HAVE NOT YET, BUT WILL BE TAKING OUR VEHICLE IN FOR EVALUATION OF THE PROBLEM AND WOULD BE ABLE TO PROVIDE DOCUMENTATION OF THE RESULTS IN THE FUTURE. GIVEN THE NAME, I AM SURPRISED MERCEDES IS NOT STEPPING UP HERE! *TR

NHTSA ID

10947866

Incident

Oct 1, 2015

Mileage

87,726 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamp/front fog lamp leaky or fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system • Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. • If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system • Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. • If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (Figure 2) and apply a maximum overpressure of 30 mbar. • The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (Figure 3). (Figure 4) • Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Figure 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. • If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is tight and there is natural physical condensation• If a higher pressure drop than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Desiccant packs can be installed for headlamps that are not leaky. Observe the following documents for installation of desiccant packs: • LI82.10-P-078302 Fogged headlamp, desiccant pack installed - open ventilation system • LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304