2016 Mercedes-Benz Sprinter 3500

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

The Office of Defects Investigation (ODI) analyzed complaint data provided by Daimler Vans USA, LLC (Daimler) as well as complaints submitted to ODI from consumers to identify incidents related to Rear Wheel Speed Sensors (RWSS) failures. ODI's analysis identified 6,710 incidents of RWSS failure (unique VINs) in MY 2012-2018 Mercedes- Benz and Freightliner Sprinter vehicles upfitted to campers or recreational vehicles (RVs) representing 81 percent of all Sprinter RWSS reports. Complaint and warranty analysis indicated that the majority of incidents (approximately 99%) were related to RWSS moisture intrusion condition in the Sprinter 3500 5-ton variant, which accounts for 98 percent of upfit campers, where moisture build-up and crystal dendrite formation develop in parked RVs and lead to sensor failures. According to the Daimler Information Request (IR) response, if the wheel speed information is detected as implausible by the Electronic Stability Program (ESP) control unit, the ESP system enters a failsafe mode where:-Driver torque requests are no longer accepted;-Cruise control, if used, would be deactivated; -The ESP/ABS system shuts off; and -Multiple warning lamps and messages advise the operator to take the vehicle to the workshop. While the majority of reports involved only ABS and/or ESP warning lights and messages on the instrument cluster due to faulty sensor signals triggering a failsafe mode, some reports cited intermittent sensor failures resulting in increased vehicle speed while in cruise control and degraded ABS or ESP. Degraded ESP functionality may impact driving stability of the 5-ton vehicle.On Feb 3, 2021, following discussion with ODI, Daimler submitted a Defect Information Report (DIR) to NHTSA describing a defect in the RWSS disabling the ESP control unit functions in approximately 48,667 MY 2012 through 2018 Mercedes-Benz and Freightliner Sprinter 3500 vehicles manufactured from Jan 4, 2012 through Oct 25, 2018 (Recall 21V-042). In its DIR, Daimler indicated that RWSS sensor failures are prevalent in camper vans due to sustained periods of non-use, during which time the moisture may not dry out, remaining inside the plastic housing package. If the moisture within the RWSS dries and the RWSS returns to normal operation, the failsafe mode and the warning lights will disappear at the next ignition cycle, but the sensor fault remains stored within the ESP control unit and can be accessed through a diagnostic evaluation. ODI will continue to monitor field experience in Sprinter non-RVs and Sprinter 2500 RVs 3-ton and 3.5-ton variants (approximately 626 vehicles).Daimler will notify owners of the recalled vehicles and advise them to take their vehicle to a Mercedes-Benz or Freightliner Sprinter dealer, who will replace the RWSS with a repackaged sensor with high robustness against moisture intrusion. Daimler began notifying dealers and owners in Feb 2021. This Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at NHTSA.gov under the following ID numbers:11352380 11351299 11350521 11348969 11342776 11342464 11341988 11341151 11340388 11338230 11337921 11331832 11331829 11331476 11331427 11331066 11328671 11325768 11325693 11322814 11322346 11320295 11319376 11317336 11311647 11310621 11308318 11254223 11253828 11252220 11196530 11194330 11164250 11145019 11141273 11139000 11138785 11124129 11094122 11394837 11390889 11390039 11389262 11387883 11387713 11386418 11383887 11383866 11382947 11377384 11376615 11376973 11375781 11375403 11374997 11374151 11373892 11373111 11366293 11365920 11365594 11365355 11365194 11364253 11364346 11363990 11363787 11362948 113629

Unshielded rear-center generator exhaust pipe positioned with approx 12 in clearance above the ground, ignited the exterior of vehicle when generator operated, causing total loss. My safety as well as my pets was put at great risk due to this design and lack of shielding. The problem has not been reproduced of confirmed by dealer or independent service center, however the fact of such pipe getting hot, and nbeing related to the generator was recognized by the dealer. There were no warning lamps, warning stickers near the electronic start switch in the vehicle; no messages or other symptoms of the problem prior to the failure. The design foreseeably exposes owners to fire risk, given owners only recognize the exhaust from the rear side of the vehicle; assume if the engine is off no exhaust heats up enough to start a grass or other fire. But, the majority of owners like myself do not know of any other exhaust outside of the vehicle is present. The shocking 12 inch proximity from the ground; at the rear of a 25 ft vehicle typically parking in car spaces with an overhang of the rear behind the rear wheels or a curb is a ridiculous fire risk to all owners, and the surrounding community. This is a design flaw still inherent in that same vehicle today,

NHTSA ID

11691967

Incident

Oct 2, 2025

Power steering return hose slipped off 1/2” and fluid leak. Has a recall, but not applicable to this vin. Although it appears to be effecting it? Secured line to best abilities.

NHTSA ID

11624000

Incident

Nov 1, 2024

The contact owns a 2016 Mercedes-Benz Sprinter 3500. The contact stated while driving approximately 65-70 MPH, the hood unintendedly opened, striking the windshield. The contact pulled to the side of the road and became aware that the latch screws had detached; however, the latch was still welded to the vehicle. The contact was able to clamp the hood down with a ratchet. The contact related the failure to NHTSA Campaign Number: 19V665000 (Latches/Locks/Linkages). The contact was referred by the Insurance provider to Safelite Auto Glass to have the windshield replaced. However, due to the damage done to the roof of the vehicle, the vehicle was not repaired. The vehicle had not been repaired. The dealer was contacted and informed of the failure. The dealer informed the contact that the VIN was not included in a recall. The vehicle had not been taken to the dealer. The manufacturer was made aware of the failure. The failure mileage was 200,000.

NHTSA ID

11590347

Incident

May 16, 2024

Mileage

200,000 mi

The contact owns a 2016 Mercedes-Benz Sprinter 3500. The contact stated that while driving at 30 MPH, the ABS warning light and the electronic stability control warning lights illuminated. The contact also stated that the motorhome was making abnormal clunking sounds. The contact was able to continue to drive at less than 30 MPH. The manufacturer was notified of the failure and advised the contact that one of the wheels must have failed to patch the ground. The manufacturer advised the contact to turn the vehicle on and off three times using the ignition key for the warning lights to disappear. The contact stated that he did so and the warning lights and warning messages disappeared; however, they reappeared the next day. The contact stated that while driving at 50 MPH and towing his Volkswagen vehicle, the transmission disengaged and the vehicle made an abnormal clunking sound. Then the transmission reengaged and disengaged causing the vehicle to lurch forward. The contact continued to drive the vehicle. The contact stated upon starting the vehicle the failure reoccurred. The RV was taken to the dealer who diagnosed that the rear axle speed sensors, knock sensors needed to be replaced, and the recall repair for NHTSA Campaign Number: 21V042000 (ELECTRONIC STABILITY CONTROL) was completed. The contact also stated that the dealer cross-fired the speed sensors which caused the computer to not allow the vehicle to drive more than 35 MPH. The vehicle was not diagnosed or repaired. The contact stated that while driving at 5 MPH, the vehicle leaned on his right side and crashed into a street sign. The air bags failed to deploy. There were no injuries sustained. A police report was not filed. The contact stated that while driving at an undisclosed speed, The warning lights reappeared and the vehicle leaned and hit the curb. The air bags did not deploy. There were no injuries sustained. A police report was not filed. The manufacturer was notified of the failures and offered the contract to trade the vehicle. The vehicl

NHTSA ID

11445998

Incident

Jan 3, 2022

Mileage

2,000 mi

trucks cut speed limit 65 to 10 normal highway i do understood %35 degrees slow down but its only %2 degrees uprise there is no power at engine rpm is shows less then 1 rpm and even if press the gas pedal all the way the truck does not accelerate like truck is lock right there very dangers any one drive back of me they are not accept that much speed change they are in dangers scarr to drive truck be couse same one get git back of truck and can get kill

NHTSA ID

11440985

Incident

Oct 4, 2021

The contact owns a 2016 Mercedes-Benz Sprinter 3500. The contact stated that while driving, several unknown warning lights illuminated. The contact pulled over and restarted the vehicle. The contact received notification of NHTSA campaign number: 21V042000 (Electronic Stability Control) however, the part to do the recall repair was unavailable. The contact called the local dealer who stated that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The approximate failure mileage was 8,000. Parts distribution disconnect.

NHTSA ID

11437198

Incident

Aug 1, 2020

Mileage

8,000 mi

The NHTSA law requires that the recall be done on a timely manner . Mercedes benz is not doing this . The wheel sensor recall is being not being done in a timely manner by Mercedes benz. They are typically making appointments 1 month to 3 months out to do a recall that takes 40 minutes to accomplish. .They are purposely endangering sprinter RV owners by their untimely repair schedule.

NHTSA ID

11434169

Incident

Aug 19, 2021

The contact owns a 2016 Mercedes-Benz Sprinter 3500. The contact received notification of NHTSA Campaign Number: 21V042000 (Electronic Stability Control) however, the part to do the recall repair was unavailable. The contact stated that while driving over a railroad track at a slow speed, the vehicle independently accelerated with the ABS, check engine, and traction control warning lights illuminated. The contact was able to safely stop the vehicle and shut-off the vehicle. Due to the failure, the contact had the vehicle towed to the dealer. Due to the parts for the repair not being available, the dealer decided to place a new, yet defective, speed sensor on the vehicle as a temporary repair and the contact drove the vehicle back home. The manufacturer was informed of the failure but offered no assistance. The contact had called three separate dealers and it was confirmed that the part would not be available until the fourth quarter of 2021. The vehicle was not repaired. The failure mileage was 23,580. Vin tool confirms parts not available.

NHTSA ID

11425081

Incident

Jun 12, 2021

Mileage

23,580 mi

ASSYST PLUS service reminder appears earlier than expected due to vehicle operating conditions Complaint The ASSYST PLUS service reminder appears earlier than expected. The customer or dealer may report that the vehicle did not reach the starting maintenance interval shown in vehicle documentation, option coding, sales literature, or the Owner's Manual. The service reminder may appear significantly earlier than anticipated even though no faults are stored and no malfunction is present in the vehicle. The remaining distance and remaining time continue to decrease normally until the service reminder is displayed. Cause This condition is not caused by a malfunction of ASSYST PLUS. ASSYST PLUS is a dynamic maintenance management system that continuously evaluates vehicle usage and opera-ting conditions to determine maintenance requirements. The starting maintenance interval specified by variant coding represents a maximum interval that may only be achieved under favorable operating conditions. Actual maintenance intervals may be significantly shorter depending on vehicle use. Vehicle operating conditions such as driving conditions, engine load, engine operating conditions, idling, short-trip operation, environmental influences, oil aging, and Diesel Particulate Filter (DPF) regeneration activity may reduce the maintenance interval from its starting value. These conditions may accelerate engine oil aging through increased soot loading, fuel dilution, moisture accumulation, and additional engine operating stress. As a result, the remaining distance and remaining time until the next service may be reduced from the starting maintenance interval. Remedy Do not replace any parts. A due service must be assumed if the maintenance data calculated by ASSYST PLUS indicates that service is required.

Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the de-sired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function. Remedy Remedy for Complaint A: Perform the following steps: 1. Disable the EGR Valve (Y27/17) by disconnecting the electrical connector. 2. Perform a test drive to check if the jolting/bucking issue resolves. 3. If the jolting/bucking is resolved, proceed to Remedy for Complaint B. 4. If jolting/bucking is still present, proceed with diagnosis to determine the root cause. Consider checking the follo-wing, but not limited to: •EGR system including the EGR Cooler, EGR Bypass Flap, EGR Temperature Sensor, and pipes for proper operati-on, excessive sooting and/or clogging, as well as EGR Bypass Flap vacuum element, switchover valve, and vacuum system. •Visually check the leak oil line or T-piece; reference LI07.00-N-059118.

OM642 DPF Filter Cracked or Broken Complaint Vehicle will not start or exhibits noisy exhaust. Check Engine Lamp (CEL) is on. Multiple control unit communication and system faults may be present, including but not limited to: 134800, 134900, 11B300, 11EC00, 15E100, 155700, 162500. Additional events codes may include: 134300, 102200, 163400, 16CE00. In many cases, multiple unrelated faults are stored due to electrical disruption from wiring damage rather than indivi-dual component failure. Cause The DPF filter is cracked, broken, or leaking, allowing hot exhaust gas to escape from the exhaust system. Depending on the location of the break or leak, hot exhaust gas may be directed toward the main wiring harness and/ or the SCR (Selective Catalytic Reduction) dosing valve assembly. This heat exposure can result in: • Internal melting of wiring insulation within the harness • Short to ground conditions and loss of communication between control units • Damage to the dosing valve and/or heated AdBlue line Damage to the wiring harness may not be visible externally, as the outer tape can remain intact while the internal wires are melted and fused together. Remedy Inspect the DPF assembly for cracks, separation, or leakage. Do not proceed with further diagnosis or component replacement until the exhaust leak source has been identified and confirmed. If any damage is found, replace the DPF filter assembly. Based on the location of the failure, inspect all components in the path of the exhaust leak, including the dosing valve assembly and main wiring harness. The wiring harness must be opened in any area exposed to the exhaust leak to visually inspect the individual wires. External inspection alone is not sufficient to determine harness condition. Repair or replace any damaged wiring in accordance with approved repair procedures. Replace any dosing system components that show signs of heat damage. Failure to identify and repair all heat-affected components will result in repeat faults or no-start conditions.

Complaint Rattling noise from underneath the vehicle. Cause One or more of the following conditions may be present: 1. The exhaust bracket from the DPF to the transmission is cracked or broken. • See Pic. 1 for an example of a broken bracket. 2. Transmission bell housing cracked or broken at the exhaust mounting area. • See Pic. 2 for an example of bell housing damage. 3. Exhaust bracket from DPF to engine (cylinder crankcase) cracked or broken. • See EPC OM651 #217 for bracket location. 4. Diesel Particulate Filter (DPF) pipe cracked at a weld joint. • Cracking may be present at bracket welds or along the DPF housing seams. • This can cause rattling noises and secondary exhaust bracket stress. • Perform a visual inspection of the DPF pipe and weld joints. Remedy Inspect all related components and repair or replace as required. Inspection and Repair 1. Inspect the exhaust bracket from the DPF to the transmission. • Check the bracket for cracks or complete separation. • See Pic. 1 for a failed example. • See EPC OM651 #550 and Pic. 3 for bracket location. • If damaged, replace the bracket. • See Pic. 4, Pic. 5, and Pic. 6 for the updated bracket design and identification. 2. Inspect the transmission bell housing. • Inspect the bell housing at the exhaust mounting point for cracks or structural damage. • See Pic. 2 for an example of bell housing damage. • Replace the transmission if damage is confirmed. 3. Inspect the exhaust bracket from the DPF to the engine (cylinder crankcase). • Inspect the bracket for cracks or broken mounting points. • See EPC OM651 #217 for bracket location. • Replace the bracket if damaged. 4. Inspect the DPF pipe. • Inspect the DPF for cracks at weld joints, especially near mounting points. • If cracking is found, replace per current aftertreatment guidelines. Correct positioning and tightening of the exhaust system are critical to prevent repeat failures. Positioning the Exhaust System 1. Position and align the exhaust system before tightening. • Support and fit the exhaust system in its installed position. • Push the exhaust system forward. • Install the DPF‑to‑transmission bracket and lightly tighten the mounting bolt. • Install the engine mount and V‑mount bolts by hand, approximately two turns. • See “Positioning of the exhaust system” image. Tightening Sequence 1. Tighten the exhaust system in the correct sequence. • Tighten engine mounting bolts to 25 Nm. • Tighten V‑mount bolts to 25 Nm. • Tighten exhaust bracket bolts to 15 Nm. • See “Tightening sequence of the exhaust system” image. 2. Verify mounting bolt locations. • Confirm correct mounting screw positions at the transmission bracket. • See Pic. 7 and Pic. 8 for mounting screw locations.

The check engine light is illuminated, or the AdBlue warning is active, with recorded faults related to AdBlue quality or concentration. Complaint Customer reports an illuminated check engine light and or an AdBlue system warning indicating AdBlue quality out of specification. The vehicle may enter reduced performance mode. One or more of the following fault codes related to the AdBlue tank may be stored: P206B31: Malfunction of the concentration sensor for AdBlue; the signal is absent. P203B31: Malfunction of the AdBlue fill level sensor; the signal is absent. P300494: The quality of the AdBlue is insufficient. Background AdBlue must meet ISO 22241 quality requirements. ISO 22241 urea content limits for AdBlue are 31.8 percent to 33.2 percent by mass. AdBlue begins to crystallize and freeze at approximately 12 degrees F. Freeze-thaw does not degrade the product when uncontaminated, and the bulk concentration returns to normal after complete thaw and mixing. Cause In cold soak conditions and during freeze thaw exposure, the tank contents may not be uniform at the time of sampling or system checks. During freezing and partial thaw, ice formation can temporarily create concentration gradients in the tank. As a result, urea percent readings can vary based on sample location and the state of thaw and mixing, which can produce apparent out of range readings even though the bulk fluid returns to normal after mixing. Remedy Testing Do not use a single urea percent reading taken from frozen, partially frozen, or not fully mixed AdBlue to make a repair or responsibility decision. Confirm full thaw and ensure tank contents are mixed before sampling. 1. Confirm full thaw - Confirm the AdBlue tank and associated components are fully thawed before sampling. - Do not sample slushy or partially frozen fluid. 2. Mix tank contents - Perform a road drive intended to mix the tank contents before sampling. - Idle time alone is not a reliable substitute for mixing. 3. Sample and measure - Take the sample and measure with the MB refractometer per the MB tool instructions. - Record the urea percent value. 4. Interpret the result against ISO 22241 limits - Within specification is 31.8 percent to 33.2 percent urea by mass. 5. Repeat if out of specification - If out of specification, repeat after an additional mixing drive to reduce sampling variation. - If still out of specification after full thaw, mixing, and repeat measurement, treat as a true out of specification result and proceed with further diagnosis per applicable MB guidance. Acceptance criteria AdBlue is within the ISO 22241 specification when the urea percent is between 31.8 percent and 33.2 percent by mass. Values outside this range are out of specification and require further diagnosis after completing the full thaw and mi-xing procedure above. Cross reference For vehicles with fault codes P206B31, P203B31, or P300494, refer to LI49.20-N-078838 for the detailed diagnostic and repair procedure. If a SCR or AdBlue warning reset is required after correction, refer to LI49.20-N-075995. Complete the diagnostic and corrective steps first. Perform the warning reset only after the underlying fault condition has been corrected. Warranty information and claim handling

EGR Valve Diagnosis & Cleaning (and EGR Cooler Cleaning) – OM642, Sprinter 906/907 Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the desired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.