Owner-reported complaints naming the engine system, filed with NHTSA
Data refreshed
Reports naming the engine itself — including stalling, misfires, oil consumption, cooling and internal engine components. Every record below is an owner-reported complaint about the 2014 RAM 1500 submitted to NHTSA — not a confirmed defect, not a recall and not a manufacturer bulletin. 343 reports on file name it.
Complaints are reports submitted by owners and drivers to NHTSA. They are not verified and do not establish that a defect exists.
The 25 most recent of 343, in the owner's own words
As is clearly a very common defect, my exhaust manifold bolts broke and the manifold warped. This is the second time this has happened. RAM knows about this problem. In fact, it is so well known that it is called "the HEMI tick". The fact that such a shoddy part has continued to be put on millions of trucks and other vehicles should warrant a recall.
The contact owns a 2014 Ram 1500. The contact stated that the ABS, BRAKE, and an unknown warning light were illuminated. The contact stated that approximately one year later, while driving approximately 5 MPH in the rain, the steering wheel jerked left and right continuously, and the brake pedal was depressed and the vehicle stopped facing on-coming traffic. The vehicle was driven to the residence. The vehicle was not diagnosed or repaired. The contact stated that the vehicle was then taken to a dealer for an oil change and spark plugs replacement; however, after driving away, the check engine warning light illuminated. The vehicle was taken back to the same dealer where it was diagnosed and determined that the ABS module needed to be replaced. The vehicle was not repaired because the parts were on back order. The manufacturer was notified of the failure. The failure mileage was 68,000.
This complaint concerns failure of the remedy for Safety Recall Z46 / NHTSA Campaign 22V406 involving the high pressure fuel pump (HPFP) on a 3.0L diesel pickup. The HPFP had previously been replaced under the recall by an authorized dealer. About 19 months later, while the vehicle was at a dealership for service, the replacement HPFP failed again during dealer testing. The dealer documented metal contamination throughout the fuel system caused by the HPFP failure. The dealer then replaced the contaminated fuel system components. After those repairs and during post-repair test driving, the vehicle developed new bottom-end engine noise. The dealer later documented connecting rod bearing damage / rod knock and recommended complete engine replacement. The vehicle had been brought in with no bottom-end engine noise, and the dealer’s intake inspection documented oil condition as OK. An independent oil analysis later showed the engine oil was normal and did not indicate long-term lubrication failure. This suggests the engine damage occurred acutely after the HPFP failure and resulting contamination event, not from routine wear. This condition creates a serious safety risk because HPFP failure can cause loss of fuel pressure, engine stall, or loss of motive power, and the subsequent engine damage raises the risk of sudden engine failure or seizure while driving. That could increase the risk of a crash, especially in traffic or at highway speeds. The failure was confirmed by the dealer and is documented in the repair order. The vehicle remains inoperable and is available for inspection upon request. I am requesting investigation into whether the recall remedy was adequate, since the recall replacement HPFP failed again and the resulting contamination appears to have led to catastrophic secondary engine damage.
The recall for the loss of signal from the tone ring in recall 66A was supposed to allow the vehicle to use the signal from the camshaft positioning sensor. This recall was completed on my truck but the loss of signal from a bad tone ring has resulted in the same condition as the original recall which is inoperability of the vehicle. This still poses a safety threat as the recall did not correct the issue. The manufacturer is now claiming that the recall period is expired and the tone ring failure will not be covered. the repair is $1700 and may still result in a failure of the vehicle to maintain propulsion as it did for me on Jan 30th, 2026. I have a case open with Stellantis to try and get an answer to this, but it is still a safety concern. case number 895950295
The ETC light came on and I brought the truck to my mechanic. The code for crankshaft position sensor came up. Apparently a faulty cps can cause the engine to shut down without warning. This is an obvious safety issue which Ram doesn’t want to repair.
The crankshaft position sensor and tone wheel failed which is the recall for 66A, was driving truck 45mph down heavily traffic roadway, truck died and stopped in the middle of road. took truck to dealership and dealer charged diagnostic fee explained to them that issue sounded like a crankshaft issue and was showing crankshaft codes. They refused to look into this and do the recall. Went and picked the truck up took it to a local mechanic, mechanic diagnosed issue come to found out it was indeed the crankshaft sensor and tone wheel that was the issue, purchased mopar oem parts and installed in vehicle, once repaired vehicle started and ran perfectly.
I was driving around 35 mph, the steering wheels suddenly have no power, really tight and hard to turn with no symptoms before and no light on dash, this was very dangerous if I was driving on the highway. Second thing is the famous "Hemi tick" happened on my truck, everyone have the Ram truck have exactly same issue but I really do not know why this issue still not have any recall yet. Please recall and make your product better and safer for your royal customer, please and please.
TICKING NOISE FROM 3.6l PENTASTAR ENGINE. SAFTEY CONCERN COULD RUIN MY ENGINE CAUSING STALLS AND MISFIREING AND SEZEING.
The contact owns a 2014 Ram 1500. While driving approximately 70 MPH, the vehicle went into LIMP Mode, and the check engine warning light and the throttle control warning light illuminated. The contact stated that the vehicle was taken to an independent mechanic and was diagnosed with turbocharger failure. The vehicle was then taken to a dealer; however, the vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was unavailable.
The contact owns a 2014 Ram 1500. The contact stated that while his wife was driving approximately 45 MPH and entering the freeway, the driver heard an abnormal popping sound, and it felt as if the vehicle had been rear-ended. The message "Throttle Alert" was displayed, and the vehicle failed to exceed 50 MPH while depressing the accelerator pedal. The driver was unable to pull over to the side of the road due to oncoming traffic. The driver was able to drive the vehicle to the dealer, where it was diagnosed that the crankshaft position sensor tone wheel had fractured and was missing. The dealer determined that the part needed to be replaced. The contact related the failure to NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling); however, the VIN was not included in the recall. The vehicle was not yet repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 199,000.
The magnetic material on the tone wheel detached causing a crank position sensor error code (P0336) and subsequent misfire while accelerating into traffic. The software had been updated per recall W58 (NHSTA 20V-475). Vehicle could be restarted but lacked full power. The vehicle is out of warranty, however, Stellantis directed that a dealer make repairs, customer pays out of pocket ($3200), and claim be submitted for reimbursement. Stellantis promptly denied the claim, despite correspondence in writing and recorded customer service phone call. A BBB complaint has been filed against Stellantis.
We have a 2014 dodge ram 1500 SLT with a 5.7 hemi. I was driving down the road and stopped at a red light and the truck shut off and wouldn't start again we had to tow it home. We had a mechanic look at the vehicle and run the codes for the truck to find out what was wrong it was a misfire in cylinder 3. We called a few mechanic shops in town to get other opinions and they all said the same thing its more than likely the lifters or the camshaft is bad and its a very common problem with this model truck with the engine and it would cost over $5,000 to fix it. I spoke to the dodge dealership in our town they said the same thing its more than likely the lifters they see it all the time and its around $5,000 plus to fix. Why is this allowed to happen if so many people are having this specific issue with this specific truck and this specific problem with the engine and cost us thousands to fix. This is a major safety issue what if the engine stopped while I was driving this could cause an accident. If you look it up online as well everyone is saying the same thing their problem was with the lifters. We haven't been able to get it fixed because of the cost and the cost to tow it to a mechanic. We just have it sitting in our driveway and when I found out so many others have this same issue something needs to be done.
Flexplate (flywheel) had tone wheel dislodge and destroy crank position sensor. After a $2200 repair quote from dealer and while at the dealer the repair shop claims the engine is failed completely and new ecodiesel engine is needed. Crankshaft is suspected failure. Vehicle had total loss of power when crank tone wheel failed. Very dangerous to find a shoulder without power while towing travel trailer. Vehicle was purchased due to longevity expected from diesel engine.
The contact owns a 2014 Ram 1500. The contact stated that the vehicle experienced rough idling with the check engine warning light illuminated. The vehicle was taken to the local dealer who diagnosed that the piston rod was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was not yet contacted. The failure mileage was 140,000. The VIN was not available.
Driving under normal conditions, truck had been running perfectly for the 3 months I owned it. Coming down a hill on the freeway, lights started blinking on the dash, then making a knocking noise, lost pressure (all control) of gas pedal, then white smoke from drivers side, then grey smoke, then completely engulfed in flames within 5 minutes of dash blinking. Complete loss of engine bay
this vehicle is equipped with 3.0 litre ecodiesel. truck has been in for numerous recalls--no problem. i have spoken to numerous buyers of these trucks with this engine and virtually everyone has replaced engine once or sometimes twice. i needed to replace toner wheel behind flywheel a couple weeks ago. this was a 1200.00 fix. stellantis's fix was to reprogram ecu so engine would not fail on highway but did not address the root cause of the problem. i find it appalling that stellantis has not been forced to extend the warranty on these engines since every customer paid extra for the longevity of diesel power. i am afraid to drive this truck since there are probably 2-3 rams every week on facebook marketplace locally with seized engines. this truck has 135000 miles and i am afraid the end is near.
The abs module for this vehicle has failed and is a major safety hazard. A known issue that has been on going with this particular part for years. I myself have waited over 6 months with a lemon of a truck because the part is on back order. We have called multiple dealerships and their response has been, “the part is on manufacturing review. “ No recall for this specific part has been issued and no dealership/insurance or Chrysler themselves have not provided us or any others with a solution.
The contact owns a 2014 Ram 1500. The contact stated while driving at an undisclosed speed, the vehicle stalled, and the engine seized. In addition, the shift to park warning light was illuminated. The contact stated that the vehicle failed to restart. The vehicle was towed to the dealer where it was diagnosed with a failed tone wheel. The contact was informed that the tone wheel needed to be replaced. The vehicle was not repaired. In addition, the contact stated that the complete fuel system and high-pressure fuel pump were replaced. The manufacturer was made aware of the failure and a case was filed. The contact referenced NHTSA Campaign Number: 20V475000 (Engine and Engine Cooling); however, the VIN was not included. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 150,000.
The contact owns a 2014 Ram 1500. The contact stated while accelerating to overtake another vehicle at 55 MPH, the vehicle lost motive power. The contact was able to pull over safely; however, the vehicle was difficult to restart. The electronic throttle control warning light was illuminated. The vehicle was taken to the local dealer where it was diagnosed. The dealer informed the contact that the failure was related to NHTSA Campaign Number: 23V411000 (Engine and Engine Cooling). The diagnostic test determined that the tone wheel needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline. The failure mileage was approximately 235,000.
The contact owns a 2014 Ram 1500. The contact stated while driving at an undisclosed speed, the traction control, ABS, and check engine warning lights were illuminated. The vehicle was taken to a dealer where it was diagnosed and determined that the ABS Module needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 70,000.
The contact owned a 2014 Ram 1500. The contact stated that while driving 60 MPH in the mountains, the check engine light illuminated. There was an abnormally strong odor of anti-freeze inside the cab. There was antifreeze coming from the tailpipe. The contact and her son noticed smoke on the side of the vehicle. The contact decreased her speed to approximately 45 MPH and was able to pull over. After stopping, the vehicle caught fire and was engulfed in flames. The contact stated that the failure was related to NHTSA Campaign Number: 19V757000 (Engine and Engine Cooling). The contact, her son, and her dog were able to exit the vehicle safely. The contact and her son sustained a traumatic injury, but medical attention was not provided. The dog sustained unknown injuries and was taken to the veterinarian for medical attention. A police report was not filed. The fire department was able to extinguish the fire. The local dealer was contacted. The vehicle was not diagnosed or repaired. Before the failure, the vehicle had been taken to the same dealer for NHTSA Campaign Number 19V757000 (Engine and Engine Cooling). The manufacturer was not made aware of the failure. The vehicle was towed to a tow lot. The insurance company deemed the vehicle a total loss. The failure mileage was approximately 100,000.
The contact owns a 2014 Ram 1500. The contact stated while driving approximately 35-50 MPH or above, the vehicle was shaking and jerking. The contact stated that the RPM became elevated before decreasing. The contact stated that the failure occurred while the cruise control was activated or deactivated. The ABS, the brake light, and traction control warning lights were illuminated. The contact who is a certified mechanic, diagnosed the vehicle and determined that the fuel cap, EVAP system, and the PCM had failed to respond to the catalytic converter, and the electronic response system for the traction control had failed. The vehicle was included in NHTSA Campaign Number: 18V332000 (Electrical System, Speed Control). The vehicle was taken to the dealer, and the contact was informed that the vehicle had been previously repaired under the recall. The dealer was informed of the failure; however, the vehicle was not diagnosed, and the fault codes were not cleared. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 290,000.
Driving on the interstate without cruise control on at 70 mph. I had a vehicle passing in the fast lane and a vehicle in front of me slowing down so I applied a little pressure to my brake peddle and my truck automatically began to accelerate on its own. I kept pushing on the brake peddle and it was stuck in a acceleration. The brakes tried slowing it down but it would not stop acceleration once I took my foot of the brake peddle it just rapidly began to pick up speed on its own again! I ended up pushing down on the break peddle long enough to turn off the engine and coast off to the side on the interstate. I was so glad it happened while I was driving it and not my wife she could of wrecked into the back of the vehicle in front of us and caused a multiple car crash! The Electronic Throttle Control (ETC) light came on while I was pushing down on the brakes to try stopping the truck, but once I turned the engine off and back on again the (ETC) did not come back on although the brake lights stayed on for about 10 miles.
This truck has many issues including emmissions problems thst cussed the truck to go into limp mode related to the boost sensors. This happened to me 3 times on the freeway when the truck flashes service electronic throttle control and power is reduced. On October 28th I was driving the truck on 55 mph roads. As I came to a 45 mph road, the engine started knocking. As I got into stop and go traffic the oil pressure started dropping to 0 and back to normal and the knock got louder. I had the truck towed into the dealership where they verbally quoted me over $24,000 for a new motor. The truck had just over 118,000 miles on it. They stated none of the repairs would be covered by the extended emissions warranty. The dealership then allowed me trade the truck in for less than the value ($16,000) causing extra thousands of dollars to be spent instead of repair. The dealership stated it would be an auction truck. On 11/6 I found that the truck had been listed on the dealerships website for $21,325. There is no mention of the repair or defects on the truck and that price is less than what I was quoted for a motor replacement.
The contact owns a 2014 Ram 1500. The contact stated that while driving approximately 70 MPH, there was a chemical burning odor inside the cabin of the vehicle. Later, while driving the check engine warning light illuminated, and the "throttle body" message was displayed before the vehicle decelerated and stalled. The vehicle was taken to the local dealer who diagnosed that the crankshaft position sensor was faulty and needed to be replaced. The vehicle was not yet repaired. The contact stated that the vehicle was previously serviced under NHTSA Campaign Number: 20V475000 (Engine, Engine Cooling); but later experienced the failure listed in the recall. The manufacturer was not yet contacted. The failure mileage was 138,000.
Higher-selling and older vehicles accumulate more reports. Counts are not failure rates and are not directly comparable between vehicles that sold in very different numbers.
Categories with enough reports to have a page of their own
Data on this page last refreshed .