2017 Ford Flex

On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently incorporated into the subject population because they use B-pillar trim pieces that are substantially similar to those used on the MY 2019 Ford Flex vehicles. In July 2025, prior to the opening of PE25007, ODI and Ford met to discuss B-pillar trim detachment in Ford Flex vehicles. Ford reported that its warranty analysis indicated that Flex B-pillar trim had a low detachment rate and that Ford did not believe this condition posed an unreasonable risk to motor vehicle safety. In July 2025, Ford closed its internal investigation. Because ODI’s analysis of complaint data indicated a high failure rate and an increasing failure trend, PE25007 was subsequently opened. In responding to the information request for PE25007, Ford reassessed the warranty search criteria used in its July 2025 internal investigation. The reassessment found the detachment rate to be substantially higher than what Ford had originally determined. Consequently, in October 2025, Ford issued recall 25V732based on the reassessed and accurate high failure rate. This recall instructed dealers to inspect the driver and front passenger B-pillar trim pieces and repair/replace if necessary. The vehicles included in this recall were MY 2017-2019 Ford Flex with production dates between February 17, 2017 and December 2, 2019. In January 2026, Ford issued 25V732 Amendment 1, which updated the remedy to remove the inspection criteria and instead proactively secure the driver and front passenger B-pillar trim with adhesive. The scope of vehicles included in the recall was unchanged by Amendment 1. ODI’s analysis of 25V732 found that both the scope and remedy were insufficient and that an unreasonable safety risk remained despite the recall. MY 2016 Ford Flex was excluded from the recall scope and the rear B-pillar trims on both the driver and passenger side were excluded from the recall. The failure rates of both MY 2016 Ford Flex and rear B-pillar trim pieces were found to be higher than the failure rates in similar trim detachment recalls issued by both Ford and other vehicle manufacturers. Starting in January 2026, ODI and Ford had multiple meetings to discuss Ford’s PE25007 response data and ODI’s concern about the 25V732 scope and remedy. In June 2026, Ford issued 25V732 Amendment 2. This amendment expanded the scope of the recall to add MY 2016-2017 Ford Flex vehicles produced before February 17, 2017. Additionally, this amendment updated the remedy to include removal of and reapplication or replacement of both rear driver and rear passenger B-pillar trim pieces in addition to front driver and front passenger B-pillar trim pieces. This updated remedy applies to all MY 2016-2019 vehicles. Ford expects to complete the mailing of remedy owner notification letters by March 26, 2027. Also, Ford informed ODI that prior model year (MY 2011-2015) vehicles were referred to Ford’s Customer Satisfaction forum for consideration of an extended warranty program. In view of recall 25V732 and its associated amendments, ODI is closing this Preliminary Evaluation (PE). The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

The contact owns a 2017 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V829000 (Structure) and 25V695000 (Back Over Prevention); however, the parts to do the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact stated that the rearview camera displayed a blank image while in reverse(R). In addition, the contact stated that the driver’s side B-pillar trim had become loose and could potentially detach from the vehicle. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The failure mileage was approximately 190,000.

NHTSA ID

11752577

Incident

Dec 1, 2025

Mileage

190,000 mi

The contact owns a 2017 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera displayed a distorted image. No warning light was illuminated. The dealer was contacted and confirmed that parts were unavailable. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 85,000.

NHTSA ID

11752005

Incident

Nov 22, 2024

Mileage

85,000 mi

The contact owns a 2017 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the rear-view camera intermittently displayed a distorted or blank image. The failure mileage was unavailable.

NHTSA ID

11745001

Incident

May 27, 2026

The contact owns a 2017 Ford Flex. The contact stated while driving at an undisclosed speed, the driver's side B-Pillar Applique Trim detached and flew off. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The dealer was made aware of the failure, and the contact was informed that the parts were unavailable. The contact received a recall notification, NHTSA Campaign Number: 25V732000 (Structure) however the parts were unavailable. The manufacturer was not made aware of the failure. The failure mileage was approximately 80,000.

NHTSA ID

11739237

Incident

Feb 18, 2026

Mileage

80,000 mi

I am submitting this complaint to report a serious and potentially dangerous safety defect involving the internal water pump design in the 3.5L Duratec V6 engine used in my 2017 Ford Flex. The water pump in this engine is mounted internally behind the timing chain cover. When the pump fails, coolant is not externally visible but instead leaks directly into the engine oil. This design prevents early detection and warning, leading to rapid and catastrophic engine failure without adequate notice to the driver. In my case, the water pump failed suddenly, allowing coolant to contaminate the engine oil. This resulted in total engine failure and immediate loss of vehicle operability.

NHTSA ID

11731995

Incident

Mar 10, 2026

The contact owns a 2017 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V732000 (Structure) and 25V695000 (Back Over Prevention); however, the parts to do the recall repairs were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

NHTSA ID

11725556

Incident

Oct 13, 2025

Hello, I recently submitted a safety complaint regarding my 2017 Ford Flex. The complaint number is XXX. I would like to add additional information that I forgot to include in the original report. The vehicle’s power liftgate has intermittently opened on its own while the vehicle was parked. There have been occasions where I came outside and found the liftgate open overnight in my driveway. This issue appears to be intermittent and part of the same electrical problems affecting the backup camera system described in my complaint. Please add this information to my existing complaint. Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11723541

Incident

Oct 1, 2025

My 2017 Ford Flex has an open safety recall for the rearview camera system (Ford Recall 25S49 / NHTSA Recall 25V695). The recall states the camera may display a blank image or show the message “Camera Unavailable” when the vehicle is placed in reverse. My vehicle is actively experiencing this exact failure. The screen frequently displays “Camera Unavailable,” preventing the rearview camera safety feature from functioning when the vehicle is put in reverse. I received the recall notice in October 2025. Since then I have contacted my Ford dealership several times and have been told that parts are still not available to repair the recall. Ford initially provided an estimated remedy date of January 2026. This date was later moved to June 20, 2026. I was recently informed that the date has now been removed completely and there is no estimated timeline for when the recall repair will be available. The safety recall remains unresolved while the defect continues to occur on the vehicle. The rearview camera is an important safety feature that assists drivers when reversing. I am submitting this complaint because the recall repair has been delayed for many months while the safety defect is actively occurring.

NHTSA ID

11723530

Incident

Jan 15, 2025

NEW VEHICLE DELIVERY HOLD - Emissions Recall 25E10 - Supplement #1 Certain 2018-2020 Model Year F-150 Vehicles With 3.3L Engines and 2016-2019 Model Year Explorer, Taurus, and Flex Vehicles With 3.5L Engines Powertrain Control Module (PCM) Reprogramming

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.