2018 Ford Flex

On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently incorporated into the subject population because they use B-pillar trim pieces that are substantially similar to those used on the MY 2019 Ford Flex vehicles. In July 2025, prior to the opening of PE25007, ODI and Ford met to discuss B-pillar trim detachment in Ford Flex vehicles. Ford reported that its warranty analysis indicated that Flex B-pillar trim had a low detachment rate and that Ford did not believe this condition posed an unreasonable risk to motor vehicle safety. In July 2025, Ford closed its internal investigation. Because ODI’s analysis of complaint data indicated a high failure rate and an increasing failure trend, PE25007 was subsequently opened. In responding to the information request for PE25007, Ford reassessed the warranty search criteria used in its July 2025 internal investigation. The reassessment found the detachment rate to be substantially higher than what Ford had originally determined. Consequently, in October 2025, Ford issued recall 25V732based on the reassessed and accurate high failure rate. This recall instructed dealers to inspect the driver and front passenger B-pillar trim pieces and repair/replace if necessary. The vehicles included in this recall were MY 2017-2019 Ford Flex with production dates between February 17, 2017 and December 2, 2019. In January 2026, Ford issued 25V732 Amendment 1, which updated the remedy to remove the inspection criteria and instead proactively secure the driver and front passenger B-pillar trim with adhesive. The scope of vehicles included in the recall was unchanged by Amendment 1. ODI’s analysis of 25V732 found that both the scope and remedy were insufficient and that an unreasonable safety risk remained despite the recall. MY 2016 Ford Flex was excluded from the recall scope and the rear B-pillar trims on both the driver and passenger side were excluded from the recall. The failure rates of both MY 2016 Ford Flex and rear B-pillar trim pieces were found to be higher than the failure rates in similar trim detachment recalls issued by both Ford and other vehicle manufacturers. Starting in January 2026, ODI and Ford had multiple meetings to discuss Ford’s PE25007 response data and ODI’s concern about the 25V732 scope and remedy. In June 2026, Ford issued 25V732 Amendment 2. This amendment expanded the scope of the recall to add MY 2016-2017 Ford Flex vehicles produced before February 17, 2017. Additionally, this amendment updated the remedy to include removal of and reapplication or replacement of both rear driver and rear passenger B-pillar trim pieces in addition to front driver and front passenger B-pillar trim pieces. This updated remedy applies to all MY 2016-2019 vehicles. Ford expects to complete the mailing of remedy owner notification letters by March 26, 2027. Also, Ford informed ODI that prior model year (MY 2011-2015) vehicles were referred to Ford’s Customer Satisfaction forum for consideration of an extended warranty program. In view of recall 25V732 and its associated amendments, ODI is closing this Preliminary Evaluation (PE). The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

The driver side C pillar trim broke off while driving on the highway causing the debris to interrupt traffic.

NHTSA ID

11766587

Incident

Aug 28, 2026

I own a 2018 Ford Flex, VIN 2FMGK5D8XJBA07166, with two open safety recalls Ford cannot repair: 25SA9 (rear view camera, NHTSA 25V695) and 25SB8 (B-pillar trim, NHTSA 25V829). My rear view camera has been completely inoperative for two years — it has not worked at all since mid-2024. On 7/12/2024 a Ford dealer verified the failure (repair order 568991), over a year before Ford issued recall 25SA9 in 10/2025. On 9/10/2026 Ford left me a voicemail stating there are no updates for 25SA9 and the 25SB8 remedy is not expected until Q1 2027 — over 15 months away. I have driven 2+ years with no functioning backup camera on a vehicle Ford knows is recalled. I request NHTSA treat this as a failure to provide a timely remedy and require Ford to provide an interim remedy or alternate vehicle and accelerate the repair timeline.

NHTSA ID

11765293

Incident

Sep 18, 2026

There's been a recall for the rear backup camera since October of last year. Although there hasn't been any particular incidents, there's been some close calls because the fix is still not available. Any help would be appreciated

NHTSA ID

11762278

Incident

Sep 4, 2026

The contact owns a 2018 Ford Flex. The contact received notification of NHTSA Campaign Number: 26V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rear-view camera displayed a black image. The vehicle was taken to two dealers, but the vehicle was not repaired due to parts not being available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 103,000.

NHTSA ID

11762143

Incident

Oct 4, 2025

Mileage

103,000 mi

Rear passenger door fails to latch properly. The door falls open on left turn.Warnings are unclear or non-existant

NHTSA ID

11761319

Incident

Aug 1, 2026

The contact owns a 2018 Ford Flex. The contact stated that while attempting to reverse, the rearview camera became inoperable. The contact stated that the rearview camera image would appear blank and other times the camera not available warning message would display. The contact received notification of NHTSA Campaign Numbers: 25V829000 (Structure) and 25V695000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The dealer was not contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The approximate failure mileage was 150,000

NHTSA ID

11760123

Incident

Aug 27, 2026

Mileage

150,000 mi

Recall has not been remedied, and it has been over six months.I was told it would be remedied by june or ford would be held accountable for compensating for repairs on the.Recall. #25SA9/25v695 The recall addresses the camera for backing up witch is still not functioning in a safety risk.

NHTSA ID

11741171

Incident

Oct 13, 2025

Wile driving 40 mph, the right rear tire locked up and I had to counter steer aggressively to avoid spinning out and hitting oncoming traffic. The car was flat bed delivered to Ford and they recommended the following repairs. "Control Arm- Rear: rear suspension lateral links. The rear upper and lower control arms not only provide suspension travel but also secure the rear end to the vehicle." "*Tires - 4: passenger rear inner sidewall damaged."

NHTSA ID

11740622

Incident

May 22, 2026

NEW VEHICLE DELIVERY HOLD - Emissions Recall 25E10 - Supplement #1 Certain 2018-2020 Model Year F-150 Vehicles With 3.3L Engines and 2016-2019 Model Year Explorer, Taurus, and Flex Vehicles With 3.5L Engines Powertrain Control Module (PCM) Reprogramming

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.