2025 Mercedes-Benz E350

On October 16, 2026, all three dashboard displays in my 2025 Mercedes-Benz E350 suddenly stopped functioning while I was driving. This resulted in the loss of critical driver information and created a significant safety concern. I brought the vehicle to an authorized Mercedes-Benz dealership for diagnosis. The dealership confirmed that all displays were completely blank and that multiple electronic control units were unable to communicate. The technician reported that disconnecting the mobile phone control unit connector restored operation of the displays. The dealership also identified corrosion and apparent liquid contamination at electrical connectors beneath the center console, including an SRS-related connector. Diagnostic fault codes documented communication failures, electrical short circuits, and faults involving the airbag and pedestrian protection systems. The dealership attributed the damage to liquid intrusion or spillage and denied warranty coverage. However, I have never spilled a beverage or any other liquid inside this vehicle. The dealership has not provided evidence establishing the source of the contamination or how liquid reached these critical electrical components. I am concerned that the placement or protection of sensitive electrical wiring beneath the center console may allow moisture intrusion to compromise multiple vehicle safety and electronic systems. The dealership estimates approximately $17,000 in repairs, including replacement of the body wiring harness, and has indicated that additional repairs may be necessary. The vehicle has been inspected by the dealership, and the affected components are available for further inspection. The underlying cause of the contamination remains undetermined. I am requesting that NHTSA investigate whether this vehicle has a potential electrical system design or component protection defect that could result in sudden loss of dashboard displays and impairment of safety-related systems.

NHTSA ID

11774761

Incident

Oct 16, 2026

The digital instrument cluster and center infotainment display screen went completely black and blank while the vehicle was in motion. This immediate failure blinded the driver to critical safety telemetry, including the current vehicle speed, gear positioning, and active safety warning telltales, creating an immediate, severe crash hazard on the roadway.This symptom is identical to the failure condition detailed in active NHTSA Safety Recall Campaign 26V281000 for this exact model year. The vehicle is currently held at an authorized Mercedes-Benz dealership (Mercedes-Benz of West Covina) where technicians confirmed the physical screen and plug blackout but are actively refusing to execute the safety recall remedy without a $1,272.95 out-of-pocket consumer diagnostic fee, falsely claiming a localized cosmetic stain on a connection plug voids the manufacturer's obligation to repair a known, federally acknowledged factory software design defect.The vehicle remains unmodified, intact, and available for federal or corporate engineering inspection at the dealership location upon request. No warning lamps or symptoms appeared prior to the sudden screen blackout.

NHTSA ID

11746077

Incident

Jun 1, 2026

Drove the car through a 6" puddle and the engine was hydro locked, alternator and starter died leaving me stranded in the middle of the road. This car is in Florida and I would expect it to be able to go through a puddle. When getting the engine replaced I was told that my E350 was not the only one with this issue.

NHTSA ID

11679037

Incident

Jun 30, 2025

Complaint Diverse functional limitations in the vehicle in combination with various warning and fault messages in the instrument cluster display. Cause Communication timeouts mean that communication errors may occur in the on‑board electrical system, which can result in various fault messages being displayed in the instrument cluster. This could be down to delayed feedback from the drivetrain control unit (N127) (CPC) to other control units networked to the CAN bus. Information: Only valid for vehicles through production period 10/2025. Not valid for vehicles with control unit CDCC (N125, central controller charging and driving) • It may not be possible to attribute any communication errors stored in the control units on the CAN bus to a specific cause • In rare instances, there may be a brief activation of the yellow warning lamp for engine diagnosis or there may be a sporadic delay with the start enable. • There may not be any specific fault codes present that indicate a specific component. Example image: Fault messages in instrument cluster: The reason for this could be down to delayed feedback from the control unit CPC3 to other control units networked on the CAN bus. Remedy Do not replace any components!!! ******************************************************************************************************* 1. Connect charger (see AR54.10‑P‑1127WT). Note: An adequate voltage from the on‑board electrical system battery must be guaranteed for the entire duration of the work procedure. Otherwise, the control units could be damaged if an undervoltage occurs. Information: Observe the operating instructions of the charger. Information: Use the charger to ensure an adequate voltage (at least 12.5 V) from the on‑board electrical system battery. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 2. Connect diagnostic system (see AD00.00‑P‑2000‑06FR). Note: Always use the latest XENTRY Diagnostics software release. Information: Strict compliance with the operation steps in XENTRY Diagnostics is absolutely essential. ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 3. Select control unit N127 (CPC) via the direct link using XENTRY Diagnosis. Information: To do so, select the following menu items: Control units view → Drive systems → N127 ‑ "Drivetrain" control unit (CPC) ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 4. Update software for control unit N127 (CPC) (see AR54.21‑P‑0014‑01Y). Info: To do so, select the following menu items: Adaptations → Control unit update → Update control unit software. Information: You are then automatically guided through the steps "Update of control unit software" and "SCN coding". Always observe the following operation steps at all times ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 5. Disconnect diagnostic device from vehicle (see AD00.00‑P‑2000‑06FR). ‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑‑ 6. Disconnect charger from vehicle (see AR54.10‑P‑1127WT).

Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, is launching an OTA update to the subject vehicles to provide an enhanced user experience. This OTA update includes enhancements to the MBUX voice assistant. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Complaint Wheezing noises/squeaking noises from the front shock absorbers when passing over surface undulations and rough road. Noise MUST match those heard in the attached videos. Cause • Wheezing noises: Flow noises of the damper oil • Squeaking noises: From the mechanical rubber valve in the dividing piston Remedy In case of complaints, the front shock absorbers must be replaced. If shocks have been replaced and noise persists, please open a TIPS case to the Body, Chassis, Entertainment inbox.

Issue A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.