2024 Mercedes-Benz EQB 300 4MATIC

I was driving very slowly down a residential side street and started to pull over to the right side to park behind a car. This parking spot was on a slight incline and the curb was made up of two slanted cobblestones. After I moved in to position within about 2 ft from the car in front of me, my car quickly accelerated and slammed in to it. While I did not notice it at the time, after noticing the nature of the damage to both cars, it appeared as though the car may have tried to swerve from the curb. I believe the front sensors detected there was something in the way and the car swerved left hitting the parked car in front of me. There were no warnings before the event and I did not notice the warnings on the dashboard when the car collided because I was too upset and got out quickly, but I definitely noticed that the dashboard was lit up. Progressive Insurance, Mercedes Customer Service and Hanover MA Dealership, and Norwell Collision have all since been involved. The car was towed to the body shop immediately after the incident. Mercedes Service at first advised me to keep the car as is until they had a chance to run tests, but then advised us to get the car repaired at the body shop so we didn't wait to long to get it back (I had told them that I would not drive it again unless Mercedes ran full diagnostics and convinced me that it was safe to drive). The body shop made the repairs and then delivered the car to Mercedes Hanover to run tests. They believe the car is fine and are delivering it back to the body shop where we are supposed to pick it up. Progressive has mailed claim checks which we are using to pay the body shop, however this is not an admittance of any wrong doing. I strongly believe that the car was at fault.

NHTSA ID

11772501

Incident

Sep 19, 2026

I own a 2024 Mercedes-Benz EQB 300 4MATIC, VIN [XXX], manufactured in XXX. I am requesting a formal safety review regarding NHTSA recall 26V073, involving potential high-voltage battery fires. The official NHTSA recall report lists XXX, as the last affected vehicle production date. However, page 5 states that the supplier production correction became effective for vehicles produced from XXX onward. My vehicle was manufactured between these dates but does not appear to qualify for the replacement recall. I do have multiple battery charging failures. I have reached out to benz as well. Please open a formal customer assistance case, provide a case number, and respond in writing with the findings of your technical review. Thank you. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11770593

Incident

Nov 11, 2025

I am submitting this complaint regarding a serious safety issue involving my vehicle. For an extended period of time, this vehicle has experienced recurring starting failures. On multiple occasions, the vehicle would not start, requiring service visits to the dealership. Despite repeated repair attempts, the dealership was unable to identify the root cause of the problem and typically performed only software updates. I was repeatedly informed that no specific defect could be found.Recently, the issue escalated into a much more dangerous event. While driving, the engine suddenly shut down without warning. The loss of engine power occurred during normal vehicle operation and created a significant safety hazard. This unexpected engine shutdown could have resulted in a collision, serious injury, or loss of vehicle control, particularly if it had occurred in heavy traffic or at highway speeds.What is especially concerning is that this incident appears to be related to the same unresolved condition that has resulted in multiple prior service visits. The vehicle has a documented history of similar symptoms, yet the underlying cause has never been identified or permanently corrected.Based on the repeated failures, unsuccessful repair attempts, and the recent engine shutdown while driving, I am concerned that this vehicle may have a safety-related defect affecting its reliability and safe operation. I am submitting this complaint so that the issue can be investigated and evaluated for potential broader safety implications.The vehicle continues to cause concern whenever it is driven because there is no assurance that the engine will not shut down again unexpectedly.

NHTSA ID

11744337

Incident

Jun 6, 2026

My vehicle is not included in the current high voltage battery recall under NHTSA recall 26V073, as it has a manufacture date of 08/2024 per door jamb sticker, however, page 5 of the NHTSA report explicitly states “A change in the production procedure of our supplier ensures that this issue can no longer occur on vehicles produced from July 31, 2024 onwards.” This leaves car production between May and July 31 (and likely beyond!) unaccounted for in the recall. My car was built in August 2024, likely with a battery manufactured prior to July 31, 2024 with the defect. I believe my car should be included in the recall/affected vehicles given its production date and the date of production remedy. I accessed the recall report here: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11727121

Incident

Mar 25, 2026

My vehicle is a 2024 Mercedes-Benz EQB 300. Despite the nationwide recall (NHTSA 26V073000) for high-voltage battery fire risk, the manufacturer is providing conflicting and dangerous safety information. I was verbally instructed by dealership representatives to park my vehicle outdoors and limit charging to 80% to avoid a fire hazard. However, when I requested written confirmation of these safety restrictions from MBUSA Corporate Retention (Case Manager: [XXX] ), my request was ignored The manufacturer refuses to put in writing that my vehicle is safe to park in my attached garage or charge to 100%, effectively leaving me with a fire hazard in my home while refusing to acknowledge the defect for my specific VIN. This is a critical failure of the recall management process. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11724420

Incident

Feb 25, 2026

Although I have not experienced safety issues myself, this exact model+year combination has been recalled more than once: 2024 Mercedes EQB 300 4matic, and when I searched by my VIN it shows recall. I’m very concerned if my car is mistakenly not included - what if it has battery issue/fire risk but I am not aware? This poses huge safety risk on day to day driving. I request an investigation on this particular VIN and reasons of why it is not in the recall list despite all infos match.

NHTSA ID

11718584

Incident

Feb 17, 2026

On [XXX] at [XXX], while I was slowly moving my car into a parking spot, the vehicle suddenly stopped for a brief moment and then, within a second, unexpectedly accelerated forward without any input from me. The car jumped onto the pathway and collided with the glass door of the property located at [XXX] ". I attempted to control the car using the brakes immediately, but the vehicle was not responding and remained out of control. There were no alert sounds or warnings before or during the incident. The vehicle finally stopped only after hitting the glass door. I strongly believe this was caused by a software or system bug, as the sudden acceleration occurred without my intervention. Please investigate this issue thoroughly, as it raises serious safety concerns. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11699909

Incident

Nov 1, 2025

For two months my EQB has been signaling high voltage when I charge it also now I’m having a problem connecting the plug to charge my car it shows red light has faulty it’s at the shop for a week now and I haven’t gotten updates about my car the cameras as well are turning black not working.

NHTSA ID

11641571

Incident

Oct 31, 2024

Complaint Slight creaking noises when steering. Cause Noises may come from one or more sleeves of the horn contact plate. Remedy Remove the horn contact plate and check the sleeves for noise; see attached video. If necessary, apply lubricant to the sleeves.

Complaint Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is similar to a tire or wheel vibration, it is usually readily noticeable that it is distinctly different if it happens at all times or only while braking. Cause Although the cause of the vibration is most likely due to excessive lateral runout on the rotor or hub/wheel bearing, the system as a whole needs to be checked for other possible contributors. 1. Prior collision damage. 2. Excessive vehicle sitting times without rotating components. 3. Wheel bearing/hub lateral runout. 4. Wheel mating interface has been overtightened (did not follow WIS torque procedures). 5. Mating interfaces have been excessively modified (painted, gouged, bent, etc...). Remedy Read through the entire attached worksheet prior to performing. After performing, please review the final page and perform work accordingly. NOTE: This document is not pre‑authorization or otherwise dealing with warranty. This is intended for diagnostic purposes only. If there are any questions on how to proceed OR The work sheet has been performed and the vehicle has returned with the same concern. Please perform the measurements as seen in the worksheet again and open a TIPS case to the Body, Chassis, and Entertainment team.

Complaint Radio station cover art does not refresh when switching stations. The UI continues to show the old station’s artwork instead of updating to the new one. Cause When a new station change request is triggered, a temporary glitch is causing the Head Unit application to fail to overwrite the previous request. This glitch is causing the cover art mismatch in the Radio application. Remedy Please do not replace any parts. Please update the Head unit software to E505.9

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10‑P‑067691. Information: In this case, do not use a damage code for the speakers in the warranty claim!

Complaint During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time. OR Rattling, humming, dry sliding/gravel noise from the electric steering system when steering (see attachment). Complaint does not impact the ability to safely steer or control the vehicle. Cause Ball screw drive (KGT) of electric steering damaged by: 1. External force due to: ‑ Hitting the curb/posts with the front wheels. ‑ Driving over obstacles (e.g. pothole/ threshold/ speed bump/ gully) at an inappropriate speed. 2. Corrosion/ water ingress through a damaged boot (see attachment). ‑ Cracks (1) ‑ High pressure cleaner (2) ‑ Animal bite (3) See various examples listed in the attachments for examples of outside influence. Remedy Remove boot clamps closest to steering gear housing on both left and right (as seen in "Steering Rack Boot Clamp Location"). Pull back boot and inspect for rust, broken end stops, water, or any other anomalies. Replace electric steering. Note: Steering gears replaced due to outside influence or damage must not be claimed under warranty!

Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. EXAMPLE: when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double‑clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. IMPORTANT: all other vehicle keys must be outside the recognition range of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 by double clicking the "Lock button" As of modification year 22/1, by press and holding the “Lock button", then double‑click the “Unlock button" at the same time. On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. For the newer BR 174, 178, 244, 248, 520, and 540, a software update must be initiated, as there is no way to perform SCN coding.