2005 Mercedes-Benz S430

The contact owns a 2005 Mercedes-Benz S430. The contact stated that while driving at undisclosed speeds, he became aware that the defroster was not working properly, affecting the visibility while driving. The contact also stated that the heater and the A/C were not working. The vehicle was taken to an independent mechanic and the failure was linked to NHTSA Campaign Number: 04V227000 (Electrical System); however, neither the VIN nor the model year was included in the recall. The vehicle was not repaired and remained with the independent mechanic. The manufacturer was made aware of the failure. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was approximately 190,000.

NHTSA ID

11592394

Incident

Jan 1, 2024

Mileage

190,000 mi

TL* THE CONTACT OWNS A 2005 MERCEDES BENZ S430. THE CONTACT STATED THAT WHILE ATTEMPTING TO START THE VEHICLE, THE BATTERY WAS DEAD AND THE INSTRUMENT PANEL WAS INOPERABLE. THE VEHICLE STARTED UP AFTER THE BATTERY WAS CHARGED HOWEVER, THE INSTRUMENT PANEL WAS STILL INOPERABLE. THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED. NEITHER A DEALER NOR THE MANUFACTURER WERE MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 206,000. ## VIN PASSED ## MERCEDES-BENZ 2005 S430 ##

NHTSA ID

11412889

Incident

Apr 17, 2021

Mileage

206,000 mi

DASH WARNINGS:: SRS INACTIVE, PRE-SAFE UNAVAILABLE, FRONT PASSENGER SEAT AIRBAG IS TURNED OFF ACCORDING TO THE LIGHT AND THERE IS NO BABY SEAT IN IT.

NHTSA ID

10926542

Incident

Jun 1, 2016

Mileage

100,000 mi

TL* THE CONTACT OWNS A 2005 MERCEDES-BENZ S430. WHILE DRIVING APPROXIMATELY 35 MPH, THE INSTRUMENT CLUSTER LIGHTS SUDDENLY SHUT OFF AND WOULD NOT ILLUMINATE. THE GAUGES WERE IMPOSSIBLE TO READ. THE FAILURE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 80,000. UPDATED 08/02/16*LJ UPDATED 08/08/16.*JB

NHTSA ID

10874526

Incident

Jun 15, 2016

Mileage

80,000 mi

TL* THE CONTACT OWNS A 2005 MERCEDES-BENZ S430. WHILE DRIVING APPROXIMATELY 30 MPH, THE INSTRUMENT CLUSTER FAILED TO OPERATE. THE VEHICLE WAS DRIVEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE INSTRUMENT CLUSTER FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 105,000.

NHTSA ID

10855240

Incident

Apr 4, 2016

Mileage

105,000 mi

ON 7-26-2015 I PURCHASED THIS VEHICLE FROM COMMONWEALTH MOTORS LLC. AFTER 24 HOURS ON THE HIGHWAY WHILE TRAVELING AT 55MPH, I CALLED BACK AND I FILED A COMPLAINT OF THE BRAKES BEING WORN TO THE METAL, THAT THE SUSPENSION WARNING LIGHTS CAME ON, THAT THE LEFT DRIVER MIRROR WAS BROKEN, AND THE REAR TIRE KEPT GOING FLAT. I RETURNED THE CAR TO THE DEALER WHOM CLAIM ITS THE STATE INSPECTOR MADE AN ERROR THEREFORE ITS THE STATES REPSONSIBILTY. I SCHEDULED A FOLLOW UP WHICH THEY DECLINE TO REPSOND TO. THE SECOND THIRD DAY THE HEAD LIGHTS WENT ON AND OUT. I TOOK THE AUTO TO A CERTIFIED BENZ DEALERSHIP AND SHOP TO FIND OUT THESES ISSUES. AFTER PAYING FOR WARRANTY ETC..ON 7-26-2015 CARS PROTECTION PLUS PURCHASED $495.00 8-8-2015 CARS PROTCTION PLUS AUTO PROTECTION WAS DENIED AFTER PAYING $495+$10.00 FILING FEE 8-1-2015 NEW BATTERY REPLACEMENT $154.24 10-30-2015 INSTALL AND REPLACE RF LOWER CONTROL ARM $165.00 WAS JUST THE START. THEN THE DRIVERS AND PASSENGERS STRUTS I WAS TOLD WAS THE CONCERN FROM THE SECOND DAY OF HAVING THE VEHICLE.

NHTSA ID

10790183

Incident

Jul 28, 2015

Mileage

30 mi

TL* THE CONTACT OWNS A 2005 MERCEDES BENZ S430. WHILE IN PARK, THE CONTACT ATTEMPTED TO SHIFT THE VEHICLE INTO THE DRIVE POSITION, BUT THE GEAR SHIFTER SEIZED AND REQUIRED EXCESSIVE FORCE. THE VEHICLE WAS TAKEN TO A MECHANIC WHERE IT WAS DIAGNOSED AS A SHIFT LOCK LEVER FRACTURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 107,000.

NHTSA ID

10743300

Incident

Mar 1, 2015

Mileage

107,000 mi

TL* THE CONTACT OWNS A 2005 MERCEDES BENZ S430. WHILE DRIVING AT AN UNKNOWN SPEED, THE STABILITY CONTROL INDICATOR ILLUMINATED AND THE VEHICLE STALLED. THE VEHICLE WAS TOWED TO THE DEALER. THE TECHNICIAN STATED THAT THE ELECTRICAL SYSTEM FAILED AND CAUSED THE GEAR TO SHIFT INTO LOW GEAR. THE TECHNICIAN ADDED THAT THE ELECTRICAL MODULE WAS UNABLE TO READ THE KEY AND THE HEADLIGHTS MALFUNCTIONED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 105,000.

NHTSA ID

10640412

Incident

Sep 10, 2014

Mileage

105,000 mi

Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute).

Complaint There are several types of complaint about noises or poor windshield wiper wiping performance: A: Wiper blades squeaking, chattering, shuddering B: The windshield is not wiped completely (streaking) C: During the downward movement water is pulled back onto the windshield from the A-pillar (Figure 1) D: After windshield cleaning, water keeps spraying onto the windshield for several wipe cycles (Figure 2) A1: The windshield and wiper blades are contaminated with residues from car washing facilities, identifiable by the water beading. The resulting differences in the friction values between the wiper blades and the windshield can excite the wiper blades to vibrate. Note: It is mostly wax residue from the washer system, but also water-repellent nano-particle coating for paint and/or silicone-based washer fluid, that could cause this problem. A partially dry windshield also has different friction values, which can likewise result in squeaking of the wiper blades A2: The wiper blades are worn by mechanical damage (wiper lip damaged by ice or insect debris, or deformed by long periods of disuse). A3: Incorrect angle of incidence of the wiper arms to the windshield. Because of this, the rubber lip of the wiper blade may not flip over at the reversal point. Cause B: B1: Wax/ dirt residues on the windshield B2: Wiper blades deformed or worn B3: Downforce of wiper arm not OK (Figure 3) Cause C: Water is pulled back onto the windshield by the differential pressure created as the wiper arm moves downwards. Cause D: Washer water collects in the fastening of the wiper blade and is blown onto the windshield by the airstream over several wipe cycles. Note and supporting information: Wiper blades are wear parts which, even when "not used" for long periods (kept in park position), may become permanently deformed and damaged. Further stresses on the rubber wiper blade arise due to various environmental influences which progressively change the effectiveness of the rubber wiper blade and accelerate the aging process. Due to the natural aging process and wear, the wiper blades should be replaced twice a year, preferably in Spring and Fall (see operator's manual). Remedy Remedy A: A1: Cleaning entire windshield with A 000 986 40 71. A2: Checking water's flow behavior after windshield has been cleaned (see Video 1). If, after cleaning, there are still areas with water beading, then the cleaning process must be carried out again until a rejection reaction is no longer present. • Note: On the vehicle in the video (Video 1), water still beads on the bottom left of the windshield. The windshield is still not properly clean, even though it appears to be clean. The windshield is only properly clean when there are no more areas on the windshield where water beads. A3: Replace wiper blades with genuine wiper blades. Important: Only exchange wiper blades if windshield no longer has water-repellent areas Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. Remedy B: B1: Clean windshield with intensive cleaner A 000 986 40 71. Important: Do not clean the wiper blades otherwise the graphite coating will be damaged. B2: Replace wiper blades with genuine wiper blades • Note: Replacement of wiper blades is not covered under warranty and can be replaced at the expense of the customer. B3: Check the wiper arm for excessive resistance in the bearing. Restore mobility or replace wiper arm if necessary. Remedy C: Problem inherent in design for which there is no technical remedy. Exception: X204 up to 02/2014. In these vehicles, it is possible to install the design configuration of vehicles as of 02/2014. This includes wiper arms (styled arms) with improved behavior in this respect. It is also necessary to replace the wiper blades because the styled arms feature a Top Lock connection (previously Side Lock).

Complaint Headlamp, front fog lamp leaky or fogged. Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304

Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute).