2008 Mazda Mazda3

The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.

The power steering on my 2008 Mazda 3 went out. I took it to a mechanic shop who diagnosed the power steering pump is creating pressure that is getting to the rack and pinion and the fluid is just bouncing off of the rack and pinion and the computer system does not know how to function, so the power steering is not working.

NHTSA ID

11652121

Incident

Jun 22, 2024

There is a plastic ring on top of the gas tank that holds down the fuel pump.I filled up my tank and looked under the car afterwards,at this time I noticed gas coming out from the tank until is was flushed with the top and then stopped.I pulled out the back seat,found the inspection plate and for sure this was and did happen,now nothing could be done at the time because the inspection plat hole was smaller than the ring,the tank had to be dropped.It had to be fixed,about $600.00 later and tank filled up it was repaired.I still have the ring and pictures where the ring was cracked around the threads.send me a e-mail address and I can send pictures and a copy of the bill.later on I went on line and discovered that I was not the only one.This happen about 2 years back.

NHTSA ID

11575037

Incident

Mar 2, 2024

Transmission control module.

NHTSA ID

11554582

Incident

Nov 10, 2023

Drivers side lower control arm failed at the lower ball joint mounting hole, allowing the ball joint to separate from the arm. All vehicle steering and control was lost due to the failure. This failure: 1. Has extreme danger for traffic fatalities. 2. Suggests substandard materials, design, or manufacturing. Control arm manufacturer: DLZ Sold by: partsgoing Vendor: Amazon.com

NHTSA ID

11475465

Incident

Jul 22, 2022

2008 MAZDA 3. CONSUMER WRITES IN REGARDS TO DEFECTIVE FUEL PUMP.

NHTSA ID

11449230

Incident

Jan 28, 2022

TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT STATED THAT THE VEHICLE EXPERIENCED LOSS OF POWER STEERING ASSIST WHILE DRIVING AT VARIOUS SPEED AND MAKING TURN. THE POWER STEERING FAILED AND THE STEERING WHEEL BECAME DIFFICULT TO TURN. THE PARKING BRAKE AND POWER STEERING ASSIST WARNING LIGHTS WERE ILLUMINATED. THE CONTACT STATED THAT THE FAILURE OCCURRED FIVE TIMES IN TWO DAYS. THE CONTACT MENTIONED THAT AN UNKNOWN RECALL REPAIR WAS COMPLETED ON THE VEHICLE FOR THE POWER STEERING, HOWEVER THE REPAIR HAD NOT CORRECTED THE FAILURE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT THAT A RECALL REPAIR WAS COMPLETED FOR THE SAME FAILURE AND IT WAS A ONE-TIME FREE FIX AND PROVIDED A CASE NUMBER. THE FAILURE MILEAGE WAS APPROXIMATELY 90,000.

NHTSA ID

11343858

Incident

Aug 5, 2020

Mileage

90,000 mi

MY MAZDA3 DIES WHILE I AM DRIVING WITHOUT ANY INDICATION OF WHAT IS GOING ON (NO CHECK ENGINE LIGHT). WHEN IT DOES, I WAIT FOR A WHILE AND IT WILL START BACK UP AGAIN! MY SHOP AND I HAVE TRIED EVERYTHING WE CAN, BUT WE CAN'T FIGURE OUT WHY IT IS DOING THAT! I CALLED THE MANUFACTURE AND THEY SAID IT WAS RECALLED FOR POWER STEERING ASSIST FAILURE AND FIXED IN 2010 BUT TO US IT SOUNDS IT IS THAT ISSUE CAUSING IT TO STOP WHILE IN MOTION! THIS CAR IS UNSAFE!! NO CAR SHOULD STOP IN MOTION FROM NOWHERE! THE MANUFACTURE SHOULD BE RESPONSIBLE FOR THAT!

NHTSA ID

11343682

Incident

Jul 15, 2020

Mileage

176 mi

AIRBAG LIGHT IS ON.....LOST POWER STEERING AT ONLY 110,000 MILES...ABS BREAK SYSTEM NOT WORKING

NHTSA ID

11341983

Incident

Jul 1, 2020

Mileage

110,000 mi

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 09-042/04 12/10/04 DESCRIPTION Some vehicles may exhibit inoperative electric rear window defroster grid lines, integral antenna concerns causing radio reception issues or terminal tabs pulled from the rear window glass. Follow the diagnostic and repair procedures included in this service information to inspect and service rear defroster grid lines, integral antenna concerns or broken terminal tabs.

This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).

If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search.