2013 Mazda Mazda3

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

The Brake Pedal consistently malfunctions, even after the replacement of the master cylinder (by independent service center). The master cylinder does not hold pressure due to a faulty ABS control unit (which, when Mazda was contacted, said that part was on backorder until September). If the manufacturer knows this is an issue and can't supply the part due to so many replacements needed in their vehicle, why is there no recall? There is no warning to the driver on the dashboard of this issue and has causes repeated issues while breaking.

NHTSA ID

11658244

Incident

Feb 1, 2024

There seems to be a lot of people who own 2012 and 2013 Mazda 3 Sedans (with SKYACTIV-G 2.0L and Halogen Type Headlights) that are dealing with the same issue I am dealing with myself. I have just purchased a used 2013 Mazda 3 with Skyactive Technology and I noticed that when I was braking the headlights would pulse on and off and would continue while I braked. I have been told there is a TSB on this issue (attached) and Mazda is well aware of this happening. This concern is caused by inadequate alternator output controlled by the PCM when the battery is under a heavy load. They are to the point now of charging people for a doing the TSB on the car that is causing the problem of the alternator not producing the proper wattage to support both the headlights and the brake lights at the same time. There are numerous online forum entries that speak of this issue with 2012 and 2013 Mazda 3's. I am very concerned that my headlights may stop working which could result in my death or the death of my occupants of my vehicle not to mention the other motorists on the road around me if my head lights were to eventually fail at night due to lack of proper wattage to the headlights. There are videos on you tube that show these pulsing headlights on Mazda's. I believe that headlights are important enough safety issue that their failing could result in death if the headlights completely failed due to the known fault in these vehicles over time.

NHTSA ID

11572005

Incident

Feb 13, 2024

Transmission Control Module malfunction. The AT light came on and the car made a jerking motion and a clunking noise. It lost power and would not shift which is very dangerous in moving traffic. It put me at risk for getting hit by another vehicle not expecting the abrupt change in speed by my vehicle. The check engine light is now lit up. There were no warning lights before the vehicle’s transmission malfunctioned. A code came up on the vehicle when tested. U0101 lost communication with TCM. From what I have read, researched, and have been told this issue is very common for certain years of Mazda 3’s including mine.

NHTSA ID

11556887

Incident

Nov 8, 2023

The contact owns a 2013 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 16V644000 (Structure) however, the part to do the recall repair was not yet available. The local dealer was contacted, and the contact was informed that the part for the recall repair was not yet available. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11540603

Incident

Aug 24, 2023

All my seatbuckels are tearing. I thought it could of been my dog, but I a certain I did not give up my seat or let him drive. My driver side is also tearing. I noticed the buckle catching when securing it, and now it has moved past snag and had a quarter inch tear that it catches on. The buckle is not wide enough for the belt. The belt is no longer able to constraint as good as when it was whole. Unknown

NHTSA ID

11537049

Incident

Jan 1, 2021

After filing up the gas tank, there is a strong smell of fuel coming from the car. It remains strong until the tank is run down to about 3/4. Gas can be seen dripping down the tank under the car. Gas drips are clearly visible on the ground. This has been an ongoing problem for approximately two years.

NHTSA ID

11526376

Incident

Jun 10, 2023

Steering becomes unpredictable and stiff accompanied by surging and loss of power. Check engine light comes on. Code P0882

NHTSA ID

11507600

Incident

Feb 15, 2023

ABS Module suddenly start failing causing brake sinks down. Almost crashed because of it. It appears to be a very common issue but Mazda still does not recall these ABS modules made by Ford/ATE. Also, it does not show any ABS warning light, which might be why not many people have called on this as they probably thought it was normal. There is all sort of communication error codes if you read with a OBDII scanner. In fact, Ford had a recall for these ABS modules, citing "stuck or slow-responding valves due to reaction with brake fluid".

NHTSA ID

11504342

Incident

Dec 22, 2022

This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 09-042/04 12/10/04 DESCRIPTION Some vehicles may exhibit inoperative electric rear window defroster grid lines, integral antenna concerns causing radio reception issues or terminal tabs pulled from the rear window glass. Follow the diagnostic and repair procedures included in this service information to inspect and service rear defroster grid lines, integral antenna concerns or broken terminal tabs.

This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.

This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).

If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.

A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern. NOTE: Before following this Service Alert repair procedure, ensure published TSBs in MGSS have been completed per model year.