2017 Ford Fusion

On August 8, 2022, the Office of Defects Investigation (ODI) opened this investigation based on 50 Vehicle Owner Questionnaires (VOQs) alleging front brake jounce hose ruptures on model year (MY) 2013-2018 Ford Fusion and Lincoln MKZ vehicles. A ruptured front brake hose results in a brake fluid leak. As a result, the driver may experience an increase in pedal travel and a reduction in the rate of deceleration, increasing the risk of a crash. It should be noted that the subject vehicles identified fell outside the scope of NHTSA Safety Recall 20V-469, which addressed front brake hoses rupturing on certain MY 2015-2018 Ford Edge and 2016-2018 Lincoln MKX vehicles. The result causes a brake fluid leak, lengthening the distance needing to stop the vehicle, increasing the risk of a crash.On March 10, 2023, Ford Motor Company (Ford) submitted to NHTSA Safety Recall 23V-162 (Ford Recall 23S12) to address front brake jounce hoses that may rupture. Ford found the rupture occurs from a localized failure of the internal reinforcement braid due to cyclic fatigue through tensile/bending and torsional inputs during suspension and steering articulations. The supplier for the front brake jounce hoses is Hitachi. This recall affects the subject vehicles equipped with non-hybrid engines and the suspect front brake jounce hoses (a total of 1,280,726 vehicles). The recall covers subject vehicles built from February 3, 2012 to July 19, 2017 when the suspect hoses were used in vehicle production. The remedy is for dealerships to replace both front brake jounce hoses with new hoses that have a revised braid material at no cost. The vehicles equipped with hybrid engines are excluded from the recall because the internal hose pressure is much lower due to the regenerative braking provided by the hybrid brake system. No failures of brake hoses on hybrid vehicles have been reported to ODI or Ford.Ford's actions address ODIs concerns at this time. Hybrid vehicles will be monitored for related failures. The agency reserves the right to take further action if warranted by new circumstances.The 103 ODI numbers cited above can be viewed at NHTSA.gov under the following ID numbers:11511014, 11510867, 11510318, 11509030, 11505993, 11504989, 11504400, 11502147, 11502082, 11501820, 11501283, 11498439, 11498296, 11496842, 11496335, 11494931, 11494851, 11494252, 11493001, 11492084, 11492070, 11491444, 11491274, 11488858, 11488027, 11487627, 11487416, 11487233, 11486150, 11484924, 11484526, 11484080, 11483948, 11483926, 11483739, 11483723, 11482773, 11482690, 11481077, 11480788, 11480294, 11480052, 11479338, 11479334, 11479252, 11479247, 11479187, 11479094, 11479048, 11478985, 11478953, 11478729, 11478216, 11476892, 11476282, 11470558, 11468994, 11467109, 11466294, 11462746, 11461217, 11456065, 11455367, 11444848, 11436419, 11436376, 11430685, 11428329, 11425083, 11421026, 11420738, 11420735, 11420298, 11418197, 11403926, 11397549, 11366991, 11366757, 11361016, 11359968, 11354569, 11352165, 11350344, 11348799, 11343929, 11343205, 11331947, 11329020, 11319596, 11310529, 11292271, 11288455, 11254787, 11253479, 11253244, 11234622, 11230669, 11230050, 11228240, 11221111, 11143630, 11129392 and 11120228.

Recurring whining, rattling, and grinding noise coming from under the engine/transmission area of my 2017 Ford Fusion Energi (HF35 hybrid transmission). The noise is present in all gear ranges, including Neutral while the vehicle is moving, but not in Park. No warning lights or trouble codes. The transmission has already been replaced once for this same issue, and the noise has come back. This matches the known HF35 differential and transfer shaft bearing failure pattern (Ford TSB 22-2396, SSM 50744). I am on disability (SSDI) and this vehicle is my primary means of transportation.

NHTSA ID

11775048

Incident

Nov 2, 2025

While driving, the vehicle suddenly lost engine power (it shut off) and displayed "auto start stop shift to P, then restart engine". The vehicle has never done this before, and thank goodness my wife did not have the kids in the car at the time. She was able to pull over safely only because she was on a small road with light traffic, and not at highway speed. Clearly, this put not only our vehicle at risk, but others as the brakes and steering became very hard to use when the engine just shut off out of nowhere. Since it happened today, I have not taken it in to be inspected as of yet. Upon my wife getting the car restarted she came the few miles straight home, where I did test the battery and it read good at 12.57 volts with the engine and accessories off. So the Motorcraft battery is good and as such should not be a cause in this case. To say the least, we have now lost confidence in this vehicle as being a safe mode of transportation.

NHTSA ID

11772488

Incident

Oct 20, 2026

The shift cable bushing on my 2017 Ford Fusion SE (VIN: [XXX]) failed and disintegrated, causing the shift selector to bind and disconnect from the transmission linkage. The gear selector shows Park while the transmission remains engaged in gear, creating a severe rollaway hazard. This matches the exact failure mechanism of NHTSA Recall Campaign 22S43 / 21V-376, but Ford claims this specific VIN was excluded from the recall scope INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11771717

Incident

Oct 14, 2026

The contact owns a 2017 Ford Fusion. The contact stated that while driving at an undisclosed speed and depressing the brake pedal to stop, the brake pedal extended to the floorboard, and the braking distance was extended. During the failure, the brake warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed that the rear hydraulic brake hoses had failed and needed to be replaced. The rear hydraulic brake hoses were replaced, and the vehicle was repaired. The failure mileage was 144,955.

NHTSA ID

11771611

Incident

Aug 1, 2026

Mileage

144,955 mi

The automatic transmission failed at approximately 59,000 miles. The vehicle was delivered to an authorized Ford dealership on 09/04/2025 for warranty repair. The transmission was replaced. The vehicle remained at that dealership approximately eight months and was returned to me on or about 05/01/2026. After return, a grinding and clunking noise was present when accelerating, turning, braking and going over bumps. A power steering line failed within days of return and emitted smoke from the front of the vehicle while driving. A "Shift System Fault" message began appearing when shifting into reverse and continues to appear intermittently. The same dealership performed three further repair visits. Their repair orders document multiple loose bolts holding the transmission mount to the transmission, an improperly installed exhaust, and a loose right hand CV shaft nut. On 08/14/2026 I took the vehicle to a second, unaffiliated authorized Ford dealership for an independent inspection. On a lift they found all four subframe bolts loose, the right front subframe bolt not fully seated and cross threaded so that it could not be tightened further, and the four smaller rear subframe bolts missing entirely. They also documented that no one-time-use fasteners had been billed on the original transmission repair. They tightened the loose bolts, replaced the cross threaded bolt, installed the four missing bolts, and confirmed by road test that the noise was eliminated. The subframe carries the engine, transmission and front suspension. The vehicle was driven approximately 1,700 miles over roughly three months, including highway driving, in this condition before the loose and missing fasteners were found. Repair orders from both dealerships are available for inspection.

NHTSA ID

11769399

Incident

Sep 4, 2025

We purchased this 2017 Ford Fusion 1.5L EcoBoost in August 2022 at 48,968 miles. At 55,940 miles, the vehicle developed a documented coolant leak requiring water-pump replacement. At approximately 75,520 miles, the coolant level was again documented as requiring attention. At approximately 84,189 miles, the vehicle experienced low coolant, low oil, white/gray smoke and rough running. Manteca Ford identified Ford TSB 22-2322 and ultimately performed a major short-block replacement. Despite this major engine repair, mechanical and drivability problems continued. At approximately 101,375 miles, we returned the vehicle to Manteca Ford specifically for loss of power and hesitation. The Ford technician verified a “noticeable loss of power” and lack of full boost. Manteca Ford diagnosed and replaced the turbocharger. The problem was not resolved. Only approximately 205 miles later, at 101,580 miles, the vehicle returned to Manteca Ford because it was still hesitating during acceleration. Manteca Ford then identified DTCs P0729, P07AA, P2703 and P2704 and documented “TRANSMISSION INTERNAL MECHANICAL FAULTS,” including an incorrect sixth-gear ratio and friction-element faults. The dealer recommended replacement or teardown of the transmission. We are extremely concerned about the safety implications of this history. Loss of power and hesitation during acceleration can create a serious hazard when merging onto a highway, entering or crossing traffic, or attempting to accelerate to avoid a collision. This vehicle has experienced repeated engine/powertrain problems despite major repairs, and we are concerned the transmission condition may have been developing during the earlier loss-of-power/hesitation complaints. We request that NHTSA evaluate this history for a potential safety-related defect or broader pattern.

NHTSA ID

11767414

Incident

Feb 1, 2023

I was driving my 2017 Ford Fusion Platinum on my way home and the wrench light came on and said check manual when i looked in my app the only thing that was in the maintenance was my 90k maintenance . my car is driving fine no RPM jumping no smoking no burning smell no shaking nothing ( the wrench light was off when i cranked it to take my daughter to work Saturday morning ) well Saturday on my way home from bring my daughter to work my check engine light came on still my car is driving fine when i looked in my Ford App at the check engine light warning which was these two warnings The transmission control system has detected the transmission torque converter clutch is not operating as expected. Additional alerts that may provide additional information may accompany this alert .A reduction in vehicle fuel economy may also occur when the fault is present. The transmission control module has detected that the torque converter clutch failed to apply. This system failsafe logic disables the torque converter clutch when this condition is present. This results in a higher than normal engine RPM's during higher vehicle cruising speeds and reduced fuel economy. now my car is still driving fine. i took it to auto zone to put the computer on it and it read this code P0741 which gives this Torque Converter Clutch Circuit Performance or Stuck Off, which indicates that the vehicle's computer commanded the torque converter clutch to lock up, but it is failing to do so. i took it to our ford dealer ship and he stated oh yes you need a whole new transmission which is 7200$ do you want to pay now .... Im shocked that my car would need a new transmission... i have seen recalls for Torque Converter for the fusion .. but my vin is not showing this recall is there anyone else experiencing this

NHTSA ID

11766215

Incident

Sep 19, 2026

Orange wrench light came on dash with see manual ( symbol represents powertrain malfunction). Car lost power and started jerky shifting between second and third gear. We limped the car home and parked until we could get an appointment at the dealership for service. Took it to dealership. They found the powertrain maintenance light wasn't on and no current or historical codes present. Dealership road tested vehicle and verified delayed harsh shifting between 2-3 gears with no codes present. Dealership states most likely has an internal failure starting in the forward, direct or intermediate clutch. Transmission would have to be torn down to diagnose cause. They recommend replacing the transmission as being more cost effective. Transmission has approximately 145000 miles (engine was replaced under 36000 miles due to head gasket failure- replace under warranty as manufuring defect found at a scheduled oil change) so odometer only shows 117000 miles. This car was purchased new and we purchased the extended warranty and service package. It has been consistently serviced on schedule by the dealership.

NHTSA ID

11764843

Incident

Sep 5, 2026

Special Field Action 26L03 Certain 2013-2024 Model Year California Emissions-Certified Vehicles Transmission Fluid Auxiliary Pump Reimbursement

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Some 2016-2017 Edge/MKX, 2017 Continental/Fusion/MKZ vehicles equipped with a 2.7L or 3.0L EcoBoost engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316, P0524 and/or P06DD with excessive oil consumption. Oil consumption may be 1 Liter (1 quart) in less than 4,800 km (3,000 miles). This may be due to the valve guides. To correct the condition replace the cylinder heads. During service and repair, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in timing gear failure and engine damage. Replacement of the bolt is critical to the repair. The bolt requires a 4 stage torque procedure. Hold the pulley using a universal holding tool OTC 4754 or equivalent. Refer to Workshop Manual, Section 303-01. The bolt torque procedure can be

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.

This article supersedes TSB 24-2345 to update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit an oil leak from the engine oil pan RTV seal. This may be due to a lack of RTV adhesion.