2002 Hyundai Sonata

THE MANUFACTURER HAS ISSUED A SAFETY RECALL NOTIFICATION AS A RESULT OF THIS INVESTIGATION.THE RECALL AFFECTS 91,202 MY 2002-2003 SUBJECT VEHICLES PRODUCED FROM JANUARY 28, 2002, THROUGH MARCH 22, 2003.THE VEHICLE RECALL POPULATION WAS DEFINED BY THE MANUFACTURER'S USE OF A NEW SUPPLIER FOR THE CHROME PLATING PROCESS BEGINNING IN JANUARY 2002, AND A PRODUCTION CHANGE IN MARCH 2003 TO IMPROVE ADHESION OF THE PLATING TO THE DOOR HANDLE.VEHICLES BEING RECALLED REPRESENT 59 PERCENT OF THE TOTAL MY 2002-2003 PRODUCTION, BUT ACCOUNT FOR 91 PERCENT OF THE CONSUMER COMPLAINTS RECEIVED.THE PROCESS CHANGE FOR MY 2002 VEHICLES RESULTED IN A DRAMATIC INCREASE IN COMPLAINTS (1200 PERCENT ON A PER UNIT RATE BASIS).MY 2003 VEHICLES BUILT AFTER MARCH 2003 PRODUCTION CHANGE SHOWED A SIMILAR DECLINE IN THE COMPLAINT RATE.BASED ON THE MANUFACTURER'S ACTION, THIS INVESTIGATION HAS BEEN CLOSED.

IN A LETTER DATED APRIL 14, 2009, HYUNDAI-KIA AMERICA TECHNICAL CENTER, INC (HYUNDAI) NOTIFIED NHTSA THAT HYUNDAIIS CONDUCTING A SAFETY RECALL OF MODEL YEAR (MY) 1999 THROUGH 2004 HYUNDAI SONATA VEHICLES MANUFACTURED PRIOR TO NOVEMBER 20, 2003 THAT ARE REGISTERED AND OPERATED IN THE FOLLOWING SALT BELT STATES AND THE DISTRICT OF COLUMBIA: CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN.HYUNDAI IS RECALLING THE VEHICLES TO REMEDY A CONDITION WHERE INTERNAL CORROSION OF THE FRONT SUBFRAME MAY LEAD TO SEPARATION OF THE LOWER CONTROL ARM AT THE FORWARD MOUNTING POINT AND/OR SEPARATION OF THE AXLE FROM THE TRANSAXLE.THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND/OR VEHICLE DISABLEMENT. THE SUBFRAMES WILL BE INSPECTED IN THE RECALLED VEHICLES USING A PROCEDURE DEVELOPED BY HYUNDAI TO MEASURE METAL THICKNESS.PARTS WITH PERFORATIONS FROM CORROSION OR WITH METAL BELOW THE SPECIFIED THICKNESS WILL BE REPLACED WITH REDESIGNED SUBFRAMES.IF THE MINIMUM METAL THICKNESS IS MET, DRAINAGE HOLES AND RUST PROOFING MATERIAL WILL BE ADDED TO THE EXISTING SUBFRAME. ODI'S ANALYSIS OF COMPLAINT DATA REVEALED THAT 98% OF THE CONSUMER COMPLAINTS WERE FROM VEHICLES EITHER ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES. SIMILARLY 99.7% OF THE WARRANTY CLAIMS WERE FROM VEHICLES ORIGINALLY SOLD OR OPERATED IN SALTBELT STATES.ODI IDENTIFIED 105 REPORTS OF LOWER CONTROL ARM DETACHMENT AND/OR AXLE SEPARATION FROM THE TRANSAXLE THROUGH ANALYSIS OF WARRANTY AND COMPLAINT INFORMATION AND CONSUMER INTERVIEWS.ONE HUNDRED THREE (103) OF THE 105 INCIDENTS INVOLVED VEHICLES IN STATES COVERED BY THE RECALL.IN ADDITION TO THE SUBJECT VEHICLES, HYUNDAI ALSO NOTED IN THE APRIL 14, 2009 LETTER THAT MY 2001 THROUGH 2004 XG300 AND XG350 WERE ALSO BEING RECALLED AS THEY WERE MANUFACTURED WITH SUBFRAMES SIMILAR IN DESIGN THE SUBJECT VEHICLES.BASED ON HYUNDAI'S DECISION TO CONDUCT A SAFETY RECALL THIS ENGINEERING ANALYSIS IS CLOSED.

THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED PRELIMINARY EVALUATION, PE08-029, ON APRIL 22, 2008, BASED ON 40 CONSUMER COMPLAINTS ALLEGING FRONT SUB-FRAME CORROSION IN MODEL YEAR (MY) 1999 THROUGH 2002 HYUNDAI SONATA VEHICLES.COMPLAINTS DESCRIBE SEVERE CORROSION OF THE VEHICLE SUB-FRAME IN THE AREA WHERE THE RIGHT-FRONT LOWER CONTROL ARM IS ATTACHED.IN SOME VEHICLES, SUB-FRAME CORROSION HAS CAUSED COMPLETE OR PARTIAL DETACHMENT OF THE CONTROL ARM, RESULTING IN WHEEL COLLAPSE OR SEPARATION. IN RESPONSE TO ODI'S INFORMATION REQUEST LETTER FOR PE08-029, HYUNDAI PROVIDED OWNER COMPLAINTS, FIELD REPORTS, AND WARRANTY CLAIM DATA FOR APPROXIMATELY 197,906 MY 1999 THROUGH 2002 SUBJECT VEHICLES SOLD OR LEASED IN THE UNITED STATES.THE BASE WARRANTY FOR THE SUBJECT VEHICLES IS 60 MONTHS OR 60,000 MILES, WHICHEVER OCCURS FIRST.ACCORDING TO HYUNDAI, PROLONGED EXPOSURE TO THE ROAD SALTS MAY RESULT IN CORROSIVE DAMAGE TO THE SUBFRAME.HYUNDAI REDESIGNED THE SUB-FRAME EARLY IN THE MY 2004 PRODUCTION (NOVEMBER 2003) TO ADDRESS PROBLEMS WITH PREMATURE CORROSION OF THE CROSSMEMBER NEAR THE RIGHT-FRONT SUSPENSION ATTACHMENT. ODI'S ANALYSIS OF BOTH COMPLAINT AND WARRANTY DATA FOR THE MY 1999 THROUGH 2002 SONATA VEHICLES SHOWS THAT THE FAILURE RATES ARE SIGNIFICANTLY HIGHER IN SALT BELT STATES, WHICH ACCOUNT FOR APPROXIMATELY 50 PERCENT OF VEHICLE SALES AND OVER 90 PERCENT OFCOMPLAINTS AND WARRANTY CLAIMS RELATED TO THE ALLEGED DEFECT (NOTE:FOR PURPOSES OF THIS INVESTIGATION THE SALT BELT INCLUDES CONNECTICUT, DELAWARE, THE DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA AND WISCONSIN).ACCORDING TO HYUNDAI, THE ALLEGED DEFECT RESULTS IN A PROGRESSIVE LOSS OF STRUCTURAL INTEGRITY OF THE SUBFRAME AND THERE IS AMPLE OPPORTUNITY FOR THE PROBLEM TO BE DETECTED (BY INSPECTION, STEERING FEEL OR TIRE WEAR ANOMALIES) AND REPAIRED BEFORE IT REACHES A STATE WHERE A SAFETY RELATED INCIDENT MAY OCCUR.HYUNDAI IDENTIFIED 4 ALLEGATIONS OF VEHICLE DISABLEMENT AND 1 ALLEGATION OF A CRASH; WHERE THE LOWER CONTROL ARM BROKE FROM THE VEHICLE WHILE DRIVING AT 55 MPH AND THE DRIVER LOST CONTROL AND DROVE INTO A YARD.THERE WERE NO REPORTED INJURIES.ODI RECEIVED A SEPARATE ALLEGATION OF A CRASH, WHERE THE COMPLAINANT ALLEGED THAT WHILE DRIVING AROUND A SLIGHT CURVE AT 65 MPH ON A FREEWAY, THE VEHICLE SUB-FRAME FRACTURED AND THE DRIVER LOST CONTROL OF THE VEHICLE AND WENT OFF THE ROAD.AGAIN, NO INJURIES WERE REPORTED.APPROXIMATELY ONE-THIRD OF THE COMPLAINTS TO ODI ALLEGE THAT THE SUB-FRAME CORROSION RESULTED IN A LOSS OF CONTROL AND/OR A VEHICLE DISABLEMENT DUE TO WHEEL COLLAPSE OR SEPARATION.THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-016) COVERING MY 1999 THROUGH EARLY-2004 HYUNDAI SONATA VEHICLES IN SALT-BELT STATES AND EQUIPPED WITH THE SUBJECT SUB-FRAME DESIGN TO FURTHER ASSESS THE FREQUENCY AND SAFETY CONSEQUENCES OF THE ALLEGED DEFECT.

THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE), PE05-059, BASED ON NINE CONSUMER COMPLAINTS OF TIRE VALVE STEM FAILURES.THE ALLEGED VALVE STEM FAILURES OCCURRED ONLY AFTER TIRE REPLACEMENT FROM THE ORIGINAL EQUIPMENT (OE) TIRE (MICHELIN 205/65R15 ENERGY MXV4 PLUS) TO A NON-OE? AFTERMARKET TIRE.NINETY-EIGHT PERCENT OF THE AFTERMARKET TIRES ALLEGED TO BE ASSOCIATED WITH THE TIRE VALVE STEM FAILURES WERE DETERMINED TO BE AFTERMARKET TIRES PRODUCED BY BRANDS OF MICHELIN GROUP (BF GOODRICH AND UNIROYAL).MICHELIN ISSUED A TECHNICAL BULLETIN ON SEPTEMBER 15, 2005 MAKING RETAILERS AWARE OF A POTENTIAL WHEEL COVER INCOMPATIBILITY WITH BF GOODRICH TRACTION T/AAND TOURING T/A PRO SERIES TIRES THAT COULD CAUSE WHEEL COVER MOVEMENT AND IN EXTREME CASES TIRE VALVE DAMAGE. MICHELIN HAS, ADDITIONALLY, REDESIGNED THE BF GOODRICH AND UNIROYAL TIRES ALLEGEDLY ASSOCIATED WITH THE VALVE STEM FAILURES, AS OF THE FIRST QUARTER OF CALENDAR YEAR 2006. THE PREVIOUS DESIGN VERSION OF BOTH TIRES IS NO LONGER AVAILABLE.NO COMPLAINTS HAVE BEEN SUBMITTED TO ODI FOR TIRES MANUFACTURED AFTER THE INTRODUCTION OF THE REDESIGNED TIRES.THERE HAVE BEEN NO ACCIDENTS, INJURIES OR LOSS OF VEHICLE CONTROL ATTRIBUTED TO THE ALLEGED DEFECT.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED.

I purchased a 2002 Hyundai Sonata from a private seller who represented the car had about 40,000–45,000 miles. However, diagnostics from O’Reilly Auto Parts showed 278,000 miles, and Hyundai’s system confirmed over 302,000 miles. The title is marked “mileage exempt,” and the seller is not the same person listed on the title, suggesting title jumping. I have repair invoices, diagnostic records, and screenshots of the original advertisement. I believe this constitutes odometer tampering and misrepresentation.

NHTSA ID

11686374

Incident

Mar 1, 2025

The contact owns a 2002 Hyundai Sonata. The contact stated that while his girlfriend was driving at a slow speed, the sub frame snapped and fractured the axle. The vehicle was towed to an independent mechanic, and the contact was made aware of NHTSA Campaign Number: 09V124000 (Suspension). The vehicle was towed to the local dealer, who confirmed that the part had been discontinued. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the part had been discontinued. No additional assistance was provided. The failure mileage was approximately 86,000.

NHTSA ID

11681942

Incident

Aug 6, 2025

Mileage

86,000 mi

The contact owns a 2002 Hyundai Sonata. The contact stated while driving approximately 15 MPH and slowing for a right turn, the contact heard an abnormal popping sound coming from the front end of the vehicle. The contact was in the middle of the turn when the vehicle lost motive power. The contact stated that the engine was still running, but the vehicle was not responding as needed. The contact turned off the vehicle and observed that the passenger’s side control arm had detached and fallen onto the street. The contact had the vehicle towed to an independent mechanic. The vehicle was diagnosed, and it was determined that the entire front end was extremely corroded. The contact was informed that the vehicle was not drivable. The vehicle was not repaired. The manufacturer was not informed of the failure. The contact researched online and related the failure to NHTSA Campaign Number: 09V124000 (Suspension). The failure mileage was approximately 204,000.

NHTSA ID

11610010

Incident

Aug 5, 2024

Mileage

204,000 mi

The contact owns a 2002 Hyundai Sonata. The contact stated while driving at an undisclosed speed, the vehicle was shaking and made abnormal sounds. The vehicle then lost motive power. The vehicle was towed to an independent mechanic who diagnosed that the failure was related to NHTSA Campaign Number: 09V124000 (Suspension) however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 145,000.

NHTSA ID

11484038

Incident

Sep 11, 2022

Mileage

145,000 mi

Made right hand turn passenger wheel cocked dead stop. When checked out was told sub frame rust apart on passenger side.

NHTSA ID

11419507

Incident

May 29, 2021

YOU DID A RECALL A NUMBER OF YEARS AGO ON THE CHROME ON THE INTERIOR DOOR HANDLES PEELING OFF AND BEING HAZARDOUS. NOW THE SAME THING IS HAPPENING TO THE CHROME ON THE GEAR SHIFT HANDLE. IT IS VERY SHARP AND HAS MADE MINOR CUTS TO THE RIGHT HAND WHILE SHIFTING THE VEHICLE. THE VEHICLE WAS STATIONARY. IT IS AN ONGOING PROBLEM AS THE CHROME KEEPS PEELING OFF A LITTLE AT A TIME.

NHTSA ID

11397968

Incident

Mar 10, 2020

Mileage

148,000 mi

ON NOVEMBER 30, 2020 AFTER SHOPPING IN FOOD STORE, STARTING THE CAT AND COMING OUT OF A PARKING LOT AND DRIVING THE CAR FORWARD, I SMELL SOMETHING BURNING. STOP & OPEN THE FRONT HOOD AND SAW SMOKE COMING OUT OF THE AIR FILTER HOUSING AND STARTED TO BURN. SOMEBODY HELPED AND PUT OUT THE FIRE WITH A FIRE EXTINGUISHER. THE CAR WAS RUNNING HOOD AND MY DAILY DRIVER BEFORE THE INCIDENT.

NHTSA ID

11384081

Incident

Nov 30, 2020

Mileage

77,000 mi

REAR SUBFRAME RUSTED AWAY AND TRAILING ARMS BOTH FELL OFF. WAS TRAVELING AND WHEN I WAS MAKING A LEFT TURN THE RIGHT TRAILING ARM BROKE OFF AND INSTANTLY MADE THE CAR ALMOST SWERVE OFF THE ROAD. I CONTINUED HOME A BLOCK FURTHER AND LOOKED TO SEE THE DAMAGE. RIGHT SIDE TRAILING ARM COMPLETELY DETACHED AND THE LEFT SIDE BARELY HANGING ON. SENT TO HYUNDAI TO HAVE LOOKED AT AND GIVEN A QUOTE. NOTHING YET...

NHTSA ID

11365401

Incident

Aug 31, 2020

Mileage

179,000 mi

The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.

Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.