2010 Hyundai Sonata

The National Highway Traffic Safety Administration (NHTSA) received a letter dated July 13, 2022, petitioning the Agency to initiate a safety defect investigation into loss of motive power allegations attributed to oil drain pan assembly failures on certain Hyundai Motor America, Inc. and Kia America, Inc. vehicles spanning Model Years (MY) 2005-2021. The Petitioners cited examples of complaints indicating that the subject vehicles were experiencing rapid loss of engine oil due to oil drain plug back outs, resulting in loss of motive power and/or catastrophic engine damage. Additional complaints were provided which alleged that the oil drain pans lack sufficient structural integrity and are susceptible to cracking. The petition itself can be reviewed at NHTSA.gov under ODI number 11481745. On September 12, 2022, the Office of Defects Investigation (ODI) opened Defect Petition (DP22-003) to evaluate the Petitioners’ request. The Petitioners have provided additional complaints within four supplemental letters dated January 31, 2023, March 21, 2023, May 23, 2023, and August 4, 2023. ODI’s evaluation included the review and analysis of the complaints and supporting information submitted by the Petitioners, as well as additional complaints submitted directly to NHTSA which referenced either the oil drain plug or a crack in the oil pan. After reviewing the available data, ODI has not identified evidence that would support opening a defect investigation into the oil drain pan assemblies of the subject vehicles. Based on a review of the available information, a loss of motive power resulting from an oil drain plug back out has not occurred between the initial sale of a vehicle and the completion of its first oil change. If during an oil change service, a technician fails to remove the existing drain plug gasket before installing a new gasket, it is likely that a proper seal between the drain plug and the oil pan will not be made. An improper seal between the drain plug and oil pan could lead to the backing out on the drain plug, resulting in the sudden loss of oil while driving. Additionally, the provided examples of oil pan cracks were localized to the immediate vicinity of the oil drain plug and/or appeared to be the result of direct-contact with a tool during servicing.  There is no information to support that a vehicle-based defect exists relating to the oil pan assembly, and instead the documented incidents are related to the failure to follow the proper maintenance procedures during oil change service. In October 2023, Hyundai published a Technical Service Bulletin (TSB) that provided detailed instructions for oil change service on its gasoline powered vehicles, specifically highlighting the need to remove and replace the existing drain plug gasket prior to reinstalling the drain plug. After a thorough review of the material submitted by the petitioner, the information already in NHTSA's possession, and the potential risks to motor vehicle safety implicated by the petitioners' allegations, NHTSA does not believe that a formal investigation is warranted. Therefore, the petition is denied. A Federal Register Notice (FRN) further detailing NHTSA’s reasons for denial of the petition will be published. The reference numbers for the complaints to NHTSA cited by the petitioner can be found in the petition submission documents in the public file for DP22-003. To review those complaints and the additional complaints ODI added to its evaluation which are cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

The Office of Defects Investigation (ODI) of the National Highway Traffic Safety Administration (NHTSA) received a petition letter dated October 10, 2021, requesting an investigation of possible defects in the electronic throttle control (ETC) system on certain Kia vehicles resulting in the opening of DP21-003. Accordingly, Model Year (MY) 2005-2016 Kia Optima/K5, MY 2006-2015 Kia Sorento, MY 2007-2016 Hyundai Elantra, MY 2007-2016 Hyundai Santa Fe, MY 2006-2015 Hyundai Sonatas are all part of the subject population. The petition was originally filed as a Vehicle Owner Questionnaire that can be reviewed at NHTSA.gov under reference (ODI) number 11439675.On November 12, 2021, ODI opened Defect Petition DP21-003 to evaluate the petitioner?s request. ODI performed trend analyses of the VOQs related to vehicle speed control issues for all the subject vehicles and found that none of the 52 Model/Model Year Hyundai/Kia vehicles demonstrated any actionable trend that warranted an investigation.Petitioners submitted 1119 VOQs and non-VOQ cases in which sudden uncommanded acceleration (SUA) or loss of motive power (LOMP) incidents were alleged.For the 1119 reports, 220 were incidents involving crashes, from which 69 subject Hyundai-Kia vehicles were inspected by Hyundai/Kia dealer technicians, Hyundai/Kia engineers, and/or third-party representatives.ODI found the inspections identified no vehicle defects related to the ETC system.Of the 220 crash-involved reports, 13 Event Data Recorder (EDR) records were downloaded successfully and 11 of those indicated driver error: (i.e.) pedal misapplication.A condition where the accelerator pedal is mistakenly applied instead of the brake pedal when the driver wants to stop the vehicle.In addition, ODI reviewed a scientific journal paper published in Forensic Science International in 2016 by Mr. Park et al ., as well as related test videos. ODI does not believe there is any evidence of uncontrollable SUA occurrences in any of the tests reviewed. NHTSA's Office of Vehicle Safety Compliance (OVSC) reviewed the allegations regarding the potential noncompliance with Federal Motor Vehicle Safety Standard No. 124.Based on the information provided, the Agency concludes there is insufficient information for us to determine if a possible non-compliance exists.Finally, both Hyundai and Kia informed ODI that all their vehicles manufactured after 2012 were equipped with an ETC management system, in which the engine speed will go to idle when the system sees signals from both the brake pedal and accelerator pedal at the same time; this is commonly known as the brake-throttle override system.After thoroughly assessing the material submitted by the petitioner, information already in NHTSA's possession, information submitted by Hyundai and Kia in response to an Information Request letter, and the potential risks to safety implicated by the petitioner's allegation, NHTSA does not believe that a formal investigation is warranted. After full consideration of appropriate factors, the petition is denied. A Federal Register Notice (FRN) further detailing NHTSA?s reasons for denial of the petition will be published.

In a letter dated August 9, 2013, Hyundai-Kia America Technical Center, Inc. (Hyundai) notified NHTSA that Hyundaiis conducting a safety recall (13V-354) involving approximately 239,000 vehicles involving model year (MY) 2006 through 2010 Hyundai Sonata vehicles (approximately 215,000)produced beginning on March 1, 2005 through January 21, 2010 and model year (MY) 2006 through 2011 Hyundai Azera vehicles (approximately 24,000) produced beginning on September 27, 2005 through November 22, 2010 that are registered in and operated or originally sold in the following 20 salt belt states and the District of Columbia: Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, and Wisconsin.Hyundai will also inform dealers to inspect/repair vehicles that were previously registered in salt belt states but are currently registered elsewhere. Hyundai is conducting the recall to remedy a defect involving internal corrosion of the rear sub frame that may lead to separation of the rear upper/lower control arm(s) at their respective mounting points and/or separation of the axle from the transaxle where they meet.This could result in a loss of vehicle control and/or vehicle disablement which may increase the risk of a vehicle crash.In response to NHTSA?s Information Request (IR) letter, Hyundai stated the Azera vehicles utilizes the identical cross member and upper/lower rear control arm components as the subject (Sonata) vehicles.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Hyundai, ODI identified 19 non-duplicative reports alleging excessive corrosion of the rear sub frame. All of the complaint vehicles were either originally sold or registered at the time of the incident in one of the salt belt states.Of these 19 reports, 9 alleged either a suspension component separation or a fracture of the vehicle's rear cross member assembly.Similarly, ODI identified 8 warranty claims of rear sub frame replacement in data submitted by Hyundai due to excessive corrosion, all of which involved vehicles originally sold or operated in a salt belt state. Based on Hyundai's decision to conduct a safety recall, (13V-354) this investigation is closed.The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10535115, 10534110, 10525976, 10524726, 10521520, 10508368, 10505463, 10490073, 10486752, 10486435, 1048354, 10473922, and 10437887.

Subject: Non-Collision Engine Compartment Fire - 2010 Hyundai Sonata (VIN: [XXX] ) ​"On dec 19 2025, my 2010 Hyundai Sonata suffered a sudden, non-collision fire that originated in the engine compartment. While there are currently no 'open' recalls on this VIN, I am formally reporting this incident as it matches the failure patterns documented in NHTSA Defect Petition DP18-003 regarding non-crash fires in Hyundai/Kia vehicles. ​Preliminary inspection of the damage shows characteristic signs of a manufacturer defect, specifically potentially related to a connecting rod bearing failure leading to an engine block puncture and oil ignition, or an electrical short in the ABS module—both of which have been subjects of major Hyundai fire investigations and class-action settlements (e.g., Engine II settlement) INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11706241

Incident

Dec 19, 2025

External Handles made of plastic continue to break and do not allow access to open car doors

NHTSA ID

11699964

Incident

Nov 8, 2025

I have had 3 door handles fall off in the last couple months I think this is safety concern i do not see any recalls.I do see that there is a lot of people complaining about this matter door handles should not be fallen off

NHTSA ID

11686797

Incident

Sep 11, 2025

Car has had check engine light on for 3 + years. Have taken it to several mechanics including a Hyundai dealership and none of them can figure out what is wrong. Have replaced water pump, belts x2 in a year (same belt) and thermostat x 3 again (all within 2 years). Dash fuel gage and Dash heating/cooling gage are completely erratic. Cruise control does not work. Due to chronic check engine light and mechanics unable to pin point the problem, car has become hazardous to drive. With that in mind, today (9/10/2025) while exiting the high way, car stalled and behaved like it was in neutral. Steering wheel also locked up at this time. Luckily was able to stop. Had to restart car and then it occurred again while driving on a side street at 35mph. The codes that are still popping up are ones that I have spent thousands trying to fix and find the root cause of the problem. What could the issue be if no mechanic can seem to diagnose and fix the issue?

NHTSA ID

11686499

Incident

Sep 10, 2025

While driving 60–70 mph on [XXX] just north of Sylmar, I suddenly heard a loud, deep “pop” from the lower part of the car. Within seconds, the engine began steaming heavily and leaking oil everywhere. I immediately turned on my hazard lights and began maneuvering toward the right shoulder, crossing multiple lanes with semis and fast-moving traffic approaching behind me. I felt unsafe and feared the car could catch fire or explode, especially with smoke and oil present. After safely exiting the vehicle, a mechanic later told me the rod bearing blew and punched a hole through the bottom of the engine block, calling it a total engine failure. He said it would require a full replacement and matched known issues with this model. There was no warning before the failure. I’m having it inspected at Hyundai of Downtown Los Angeles on July 28. I believe this event posed a serious safety hazard to me and others on the road. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11676434

Incident

Jul 25, 2025

The contact owns a 2010 Hyundai Sonata. The contact stated that upon attempting to turn the ignition key in the ignition switch to start the vehicle, the ignition switch failed to turn, and the steering wheel locked. The vehicle was towed to an independent mechanic, where the ignition switch was replaced; however, the vehicle failed to start. The mechanic determined that an unknown part needed to be replaced. The mechanic contacted the manufacturer for parts and was informed that the unknown part had been discontinued. The vehicle was not repaired. The failure mileage was unknown.

NHTSA ID

11591509

Incident

May 22, 2024

Fuel pump failure, causing car to stop immediately on highway.

NHTSA ID

11591412

Incident

May 28, 2024

The contact owns a 2010 Hyundai Sonata. The contact stated while driving at various speeds, the steering wheel was constantly pulling to the right. The contact had to steer to the left to keep the vehicle centered. The failure persisted even after wheel adjustments had been made. The vehicle was taken to an independent mechanic where it was diagnosed and determined that an alignment was needed. The wheels were aligned. The manufacturer had been made aware of the failure. The failure mileage was 70,000.

NHTSA ID

11577080

Incident

Mar 13, 2023

Mileage

70,000 mi

The National Highway Traffic Safety Administration (NHTSA) has identified the presence of substandard and dangerous driver’s-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

The National Highway Traffic Safety Administration (NHTSA) has issued an urgent safety advisory regarding dangerous, counterfeit driver‑side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or non‑certified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

This bulletin provides information regarding condensation related to the accumulated moisture in the headlamp, rear combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This bulletin contains information about the proper removal of the windshield wiper blade protective cover on all models. If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin provides important checkpoint guidelines when performing engine oil and filter change services.

Hyundai applies a Paint Protection Film (PPF) on new vehicles before delivery to dealerships. It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.