2000 Toyota Corolla

The contact owns a 2000 Toyota Corolla. The contact stated that while the vehicle was parked and unoccupied for under an hour, a fire started inside the cabin of the vehicle. The fire was self-extinguished. Neither a Fire Department nor a Police report was filed. The vehicle was not destroyed; however, the middle interior of the center console was destroyed. The vehicle was towed to the residence, and an independent mechanic inspected the vehicle and informed the contact that the fire had originated in the power outlet. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was 200,000.

NHTSA ID

11755309

Incident

Oct 1, 2024

Mileage

200,000 mi

2000 TOYOTA COROLLA BURNING EXCESSIVE AMOUNTS OF OIL. I'M HAVING TO ADD A QUART EVERYTIME I PUT GAS IN. I DRIVE FROM DESTINATION TO DESTINATION FOR WORK AND HAVING TO OIL IS A SAFETY CONCERN AS THE LIGHT DOES NOT COME ON UNTIL IT IS EMPTY.

NHTSA ID

11130924

Incident

Sep 2, 2014

Mileage

145,000 mi

I OWN A 1998 COROLLA AND A 2000 COROLLA BOTH HAVE DRIVERS SEAT BELT ISSUSES. IN EACH CASE THE BELT RECEIVER WILL NOT LATCH

NHTSA ID

11099277

Incident

May 3, 2018

Mileage

190,000 mi

TAKATA RECALL: I DID NOT RECEIVE A RECALL NOTICE ABOUT MY AIRBAGS AND I'M TRYING TO FIND OUT IF MY CAR WAS EVER RECALLED FOR DEFECTIVE AIRBAGS. TOYOTA WILL ONLY TELL ME IF THE CAR IS UNDER A RECALL PRESENTLY. IF IT EVER WAS, THE NOTICE MIGHT HAVE BEEN SENT TO THE PREVIOUS OWNER THAT I BOUGHT THE CAR FROM IN 2001. IF THERE EVER WAS A RECALL ON THE AIRBAGS, DOESN'T TOYOTA STILL NEED TO REPLACE THEM??

NHTSA ID

11000612

Incident

Jan 31, 2001

2000 TOYOTA COROLLA. CONSUMER WRITES IN REGARDS TO WHILE DRIVING VEHICLE CHECK ENGINE WARNING LIGHT ILLUMINATED, FOLLOWED BY HEAVY SMOKE POURING FROM UNDERNEATH HOOD AND NOTICED RADIATOR CAP WAS MISSING DUE TO A NEGLIGENT ACT BY AN ESTABLISHMENT WHO SERVICED HIS VEHICLE.. *LD THE RADIATOR CAP WAS NOT SECURED AFTER HAVING AN OIL CHANGE. TWO INDEPENDENT MECHANICS STATED THE HEAD GASKET WAS COMPLETELY DESTROYED AND THE ENGINE BLOCK WAS WARPED AND A COMPLETE ENGINE REPLACEMENT WAS NEEDED AS A DIRECT RESULT OF NEGLECTING TO PLACE THE RADIATOR CAP BACK ON THE RADIATOR. *JB

NHTSA ID

10838414

Incident

Sep 11, 2015

THE 1ZZFE ENGINE DESIGN BURNS EXESSIVE AMOUNTS OF OIL. KNOWN TO HAVE POOR RING DESIGN. TOYOTA REFUSES TO HONOR WARRANTY. NOW I AM UP TO 1 QUART CONSUMPTION PER TANK OF FUEL.

NHTSA ID

10775925

Incident

Aug 1, 2000

TL* THE CONTACT OWNS A 2000 TOYOTA COROLLA. THE CONTACT RECEIVED A NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V286000 (AIR BAGS) HOWEVER, THE RECALL PART WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER HAD EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE.

NHTSA ID

10762682

Incident

Jul 19, 2015

THE HEADLINER ON THE BACK SIDE OF THE VEHICLE IS COMING APART

NHTSA ID

10731711

Incident

Jun 1, 2015

Mileage

106,000 mi

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.