2007 Toyota Corolla

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

The Agency received a petition on September 11, 2014 requesting an investigation into, low-speed surging in the 2006-2010 Toyota Corolla [vehicles] with ETCS-i, in which the brakes fail to stop the vehicle in time to prevent a crash.NHTSA conducted a technical review of the material cited and provided by the petitioner, material Toyota submitted in response to a NHTSA formal request, interviews with complainants and manufacturer representatives, as well as the results of testing of the complaint vehicle.Taking into account the allocation of agency resources, agency priorities, and the likelihood that an additional investigation would result in a finding that a defect related to motor vehicle safety exists, NHTSA has concluded that further investigation of the issues raised by the petition is not warranted.The agency accordingly has denied the petition.The official petition denial, as published in the Federal Register, is available in the document file for this defect petition, as well as copies of reference material related to the denial.Regarding the VOQs associated with the closing of this investigation, the scope as defined by the petitioner is MY 2006 through 2010 Toyota Corollas.Of the 163 VOQs submitted by the petitioner, 149 are within that specific population (11 of the 163 were outside the model and model year scope of investigation as defined by the petitioner and 3 VOQs were submitted by owners from foreign countries) and 6 of the 163 are duplicate submissions.Therefore, there are 143 unique vehicles vins are within the specific population.Of the 143 only 105 fit the alleged defect category as defined by the petitioner.The single complaint and crash noted in the Failure Report above is the petitioner's VOQ.The 143 VOQs are: 10165337, 10166526, 10209540, 10216514, 10256808 (duplicate with 10266580 and 10335955), 10272505, 10293497, 10293688, 10294727, 10297407, 10298012, 10302217, 10302877, 10303106, 10303469, 10303730, 10304192, 10305748, 10305845, 10306012, 10306480, 10307953, 10310973, 10311137, 10311176, 10311185, 10311756, 10312246, 10312272 (duplicate with 10343088), 10312771, 10313972, 10314880, 10315240, 10315442, 10315836, 10315927, 10316192, 10316627, 10316643, 10316800, 10316952, 10317128, 10317598, 10317725, 10317804, 10317894, 10317972, 10317978, 10318562, 10319589, 10320693, 10320720, 10322163, 10322213, 10322333, 10322415, 10324355, 10325755, 10326481, 10327623, 10328492, 10328519, 10329537, 10330026 (duplicate with 10356866), 10330952, 10332679, 10334005 (duplicate with 10340570 and 10547602), 10334028, 10334628, 10334936, 10336649, 10339772, 10339969, 10341515, 10342670, 10342932, 10343174, 10344874, 10345714, 10348120, 10350342, 10351112, 10352668, 10352691, 10353587, 10358767, 10359645, 10360875, 10360905, 10361254, 10363529, 10363685, 10363866, 10364127, 10366100, 10366413, 10369073, 10369494, 10371991, 10376535, 10376721, 10377193, 10379320, 10380210, 10381365, 10381849, 10382018, 10392618, 10396747, 10402827, 10412382, 10433860, 10437011, 10437801, 10450183, 10461118, 10479582, 10482133, 10489344, 10494568, 10496026, 10499932, 10520195, 10521013, 10523677, 10534094, 10537426, 10543949, 10549101, 10551478, 10552563, 10558153, 10562577, 10564980, 10566370, 10572873, 10578871, 10579722, 10587140, 10597296, 10621449, and 10637908 (which is the petitioner's VOQ and not one of the 163 submitted with the petition).The three VOQs that were submitted from foreign countries: 10303105, 10303749, and 10308974. The eleven VOQs that are out of the specified population by model or model year: 10447756, 10453401, 10490200, 10507434, 10521377, 10563214, 10563585, 10575230, 10583796, 10584534,

On August 26, 2010, Toyota submitted a Defect Information Report to the National Highway Traffic Safety Administration (NHTSA) regarding problems with Engine Control Modules that could result in engine stall while driving in certain model year (MY) 2005 through 2008 Toyota Corolla, Corolla Matrix and Pontiac Vibe vehicles equipped with the 1ZZ-FE engine and two-wheel drive and manufactured between April 19, 2004 and January 2, 2008.Toyota's report indicated that cracks may develop at certain solder point or on varistors on the ECMs.According to Toyota, such cracks generally resulted in engine warning lamp illumination, harsh shifting or engine no-start.In some cases, if the cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven.Toyota will notify owners of subject vehicles that they should return their vehicles to a Toyota or Pontiac dealer.Dealers will be instructed to inspect the production number of the ECM for each vehicle and replace the ECM if necessary.On November 30, 2009, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE09-054) to investigate alleged engine stall while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles.In its response to ODI's information request, submitted on March 2, 2010, Toyota indicated that it had identified two possible conditions with ECMs used in MY 2005 through 2007 Toyota Corolla and Matrix vehicles:1) cracks forming between the IC and the board caused by an improperly cured conformal coating applied to the circuit boards after the soldering process is completed; and 2) cracks occurring in a variable resistor (varistor) due to overheating.During the manufacturing process a glass coating is created on the surface of the varistor.Between March and August 2010, Toyota began collecting ECMs from the field to further investigate failure modes that may result in engine stall.Toyota also conducted durability testing on ECMs collected from in-use vehicles to assess whether the problems may be a continuing trend. In addition, they conducted durability testing in order to assess whether this problem was a continuing trend.Toyota found that 4 of 32 collected ECMs malfunctioned after thermal shock testing.Toyota also confirmed that cracking could develop at solder points on the ECM circuit board that could lead to engine stall while driving and that this trend was likely to continue.The manufacturer failure data in this resume is limited to MY 2005 through 2007 Toyota Corolla and Corolla Matrix vehicles.Based on Toyota's recall, this Engineering analysis has been closed.

Air bag lights is on all the time, tried to re-attached the connection under passenger seat still same issue

NHTSA ID

11748122

Incident

Jun 26, 2025

Odometer Fraud. The contact's aunt purchased a 2007 Toyota Corolla. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 180,000, and at the time of registration, it was discovered that the mileage was 195,000.

NHTSA ID

11701578

Incident

Nov 25, 2025

Mileage

195,000 mi

I was driving down the street and all of a sudden I couldn't accelerate. I pulled over and I turned off the car and then tried restarting it but it wouldn't. It said on the gear shift it was in park, but come to find out, my gear shift bushing broke while I was driving. I KNOW I'm not the only driver this has happened to either in the year, make and model.

NHTSA ID

11686864

Incident

Sep 11, 2025

Uncontrolled maximum acceleration after shifting into gear. Occurred after shifting gears such as parking. It represents a definite safety issue. There is no warning of occurrence. It has happened about 6 times in the past 4 years. I do not drive often. I contacted Toyota who referred me to the dealer. I had it checked by the Toyota dealer, who denied there is a problem. I would welcome a independent inspection. I have notified the National Highway Traffic Safety Administration in April but have heard nothing from them since.

NHTSA ID

11667454

Incident

Apr 1, 2025

The contact owns a 2007 Toyota Corolla. The contact stated that after starting the vehicle, there was an intermittent unintended acceleration without the accelerator pedal being depressed. No warning light was illuminated. The contact depressed the brake pedal, and the vehicle was able to be stopped. The vehicle was taken to an unknown dealer, but no cause for the failure was found. The dealer replaced the floor mats. The contact stated that the failure recurred intermittently. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 23,000.

NHTSA ID

11652063

Incident

Jan 1, 2021

Mileage

23,000 mi

Me chocaron mi carro lo lleve para que me lo arreglaran y se lo llevaron alos angeles ca me dieron una direccion donde dicen que lo tienen esta en una casa abandonada [XXX] pero tengo miedo arrimarme ya que temo por mi seguridad INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11611885

Incident

Aug 24, 2024

The car wouldn’t break a few months back causing it to smash into the person infront of me ever since then and getting repaired nothing has fixed it.

NHTSA ID

11590798

Incident

Oct 11, 2023

Airbag light appeared on 1/29/24 next to engine light.

NHTSA ID

11568738

Incident

Jan 29, 2024

Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.

Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.

The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.

To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.

Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.

Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.