2026 Ford F-350 Sd

When using the rear camera while towing a trailer, the image is partially blocked by a persistent message stating “full view not available”. This creates a safety issue as it obscures the driver’s view of the trailer and/or the trailer load. It is critical to be able to monitor the trailer and the load during towing to ensure a hazardous condition is not developing. I believe the rear view camera is working as designed, that is I do not believe there is a defect or failure in the hardware. However the design of the message is the problem. If the driver needs to know that “full view not available” then the message should be moved to a different part of the screen to not obscure the view of the trailer.

NHTSA ID

11771195

Incident

Oct 14, 2026

The trailer light control module is intermittently causing trailer light faults messages and signal failures. This is associated to recall 26C10. The software update doesn’t correct the problem. Ford does not have the hardware on hand to replace the failing part. This is a safety issue for us who are on the road towing travel trailers.

NHTSA ID

11764803

Incident

Apr 1, 2026

When we plug our F350 into our fifth wheel trailer, the lights work until we put the brakes on once we apply the brakes the rear right brake light and turn signal no longer work. So we are forced to drive with only one working brake light and tail light when we disconnect and reconnect. It does the exact same thing again we have had two other pick ups both GM products connected to our trailer and it works perfectly. We’ve had a mechanic look at it and tell us it was not our trailer. It is our truck. I’ve contacted Ford who refuses to do anything about it. We get brake module error messages from the truck as well as brake lighting, module errors from the truck.

NHTSA ID

11755987

Incident

Aug 10, 2026

I purchased my 2026 Ford F-350 Platinum from Sandy Sansing Ford Lincoln on June 11, 2026. I was not informed that the vehicle has two unrepaired/unresolved Recall's. Both of the recalls were issued in March, 2026. The Dealership had this vehicle on their lot from September, 2025 to the date that I purchased it. The first recall is 26E01 "Powertrain Control Module PCM Software" and the second recall is 26C10 "Trailer Module Reprogramming." I was not aware of and it was never brought to my attention at the time of sale that the vehicle had two recalls and, I purchased the vehicle three months after both of these recalls were issued.

NHTSA ID

11747451

Incident

Jun 11, 2026

Recall service not available right now. We have a remedy but parts are not available right now. We will inform you when the service is available. Or, you can contact your dealer.Description On your vehicle it is possible that the trailer module trm may lose communication at vehicle start-up. If a trm loss of communication occurs and a trailer is connected to the vehicle, trailer stop lamps and turn signal indicators will not function. Additionally, for trailers equipped with electronic trailer brakes, the trailer brakes will not function. This loss of communication can occur with-or-without a trailer connected to the vehicle and can only initiate at vehicle start-up. If this occurs, a trailer brake module fault notification will pop-up on the vehicles instrument panel cluster. The vehicle brake and turn signal lamps will continue to operate normally and are not affected by this trm fault. If you do not tow with your vehicle, you may wait for ota deployment for your vehicle remedy. Safety Risk This may result in inoperable trailer brake lights, trailer turn signals and trailer braking functions that can reduce a drivers ability to control an attached trailer and make the trailer less visible to other drivers, increasing the risk of a crash. Remedy Software is available to repair your vehicle. Ford Motor Company has authorized your dealer to reprogram your vehicles trm free of charge. Next Steps Contact your dealer for more information to schedule the free service.

NHTSA ID

11744637

Incident

Mar 18, 2026

Description On your vehicle, it may be possible to experience a noisy, partially inoperable, or completely inoperable heating ventilating and air conditioning HVAC blower Motor. Safety Risk An inoperable or partially inoperable HVAC blower Motor may affect windshield defrost and defogging capability, which can decrease visibility under certain driving conditions, increasing the risk of a crash. Remedy Parts are available to repair your vehicle. Ford Motor Company has authorized your dealer to inspect and possibly replace the blower Motor assembly. Free of charge. Next Steps Contact your dealer for more information to schedule the free service.

NHTSA ID

11743721

Incident

Oct 27, 2025

Vehicle will lurch on cold start up. This occurs while in park on a level surface.

NHTSA ID

11742423

Incident

May 6, 2026

pre-collision assist does not give audible, alert or brake did over 50 high risk test with people, automobiles and boxes at high speeds Test drove another F350 at the Dealer lot with the same problem I believe this is a module build issue with the Software [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ID

11735091

Incident

May 1, 2026

Some of the vehicles listed in the Model statement above may exhibit the HVAC (heating, ventilation, and air conditioning) and radio system turning off or radio may have no audio during snowplow operation. This may be due to the software in the powertrain control module (PCM).

Some 2024-2026 F-Super Duty vehicles equipped with a 360-degree camera may exhibit a distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q1 of 2027. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. <br /><br /> If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS "Vehicle ID" screen. Fill out the GC

This bulletin supersedes 26-2297. Reason for update: Add 2022-2025 Transit vehicles. Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display screen after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.

Some 2023-2026 F-Super Duty vehicles equipped with a trailer brake control module and built on or before 08-May-2026 may exhibit a "Trailer Disconnected" message after cycling the ignition off and back on with a trailer connected. This may be due to the presence of an integrated battery charger on a trailer equipped with electric over hydraulic brakes. If trailer functionality is restored after unplugging and plugging the trailer connector back in while the ignition is on, this condition can be corrected by downloading and performing the "Trailer Brake Configuration" application using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 19H332 and labor operations 12651D and 12651D4. Workshop Manual (WSM), Section 417-01 Exterior Lighting > Diagnosis and Testing > Trailer Lamps > Pinpoint Test G The Message Center Displays A False Trailer Disconnected Message When A Trailer Is Connected To The Vehicle - Only For Electric Over Hydraulic (EOH) Equipped Trailers When Vehicle Trailer Brake Type Setting Is Set To Electric Over Hydraulic has bee

26C37 Recall remedy Prevents a potential rearview camera image obstruction caused by a menu displaying on top of it

For 20202026 vehicles equipped with the 10R140 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.