2020 Nissan Altima

NHTSA is opening this audit query to investigate whether The Hertz Corporation (Hertz) has complied with the requirements of the National Traffic and Motor Vehicle Safety Act (Safety Act). The Safety Act requires, among other things, that a rental company shall not rent a vehicle subject to a safety recall unless the recall remedy has been performed. 49 U.S.C. § 30120(i).NHTSA is in receipt of information that indicates Hertz rented vehicles to customers without having performed required recall repairs. Accordingly, we are opening this audit query to seek additional information concerning this issue.

On December 13, 2023, the Office of Defects Investigation (ODI) opened PE23-023 to investigate allegations of engine failures leading to loss of motive power in model year (MY) 2021-2023 Nissan Rogue; MY 2019-2021 Nissan Altima; and MY 2019-2021 Infiniti QX50 vehicles. At that time, ODI had received 6 Vehicle Owner Questionnaires (VOQ) and multiple early warning reports, with consumers reporting engine knocking noises accompanied by a loss of engine power while driving. The investigation identified bearing failures in certain vehicles equipped with the subject 3-cylinder 1.5L or 4-cylinder 2.0L variable compression turbo (VC-Turbo) engines. ODI also identified early warning reports describing thermal incidents that occurred immediately after the vehicle suffered a catastrophic engine failure.  The failures were the result of a manufacturing defect in specific engine bearings (main, A-, C-, and L-link) or other engine components that may cause engine damage and potentially lead to engine failure. Engine failure can result in a loss of motive power event that can increase the risk of a crash.  Engine failure might also result in a fire if internal components detach and impact the engine block creating a hole that allows engine oil to reach hot surfaces. In its April 2024, May 2024, and June 2025 responses to ODI’s information requests, Nissan provided 998 customer reports (including complaints, field reports, and legal claims) and 1,107 warranty claims related to the alleged defect.  When combining ODI and manufacturer report data, there are 1,878 unique VINs that have experienced failures across all subject vehicles.  In one of the early warning reports, ODI identified an incident involving a 2022 Infiniti QX55 that resulted in an engine fire following an alleged engine failure. The 2022 Infiniti QX55 was not included in the scope of this investigation but the vehicle model shares the same 4-cylinder 2.0L variable compression turbo engine.  Based on the information included with the early warning report, the fire can be directly related to the alleged defect.   A further review of ODI and manufacturer data, identified 12 allegations of engine compartment fires in subject vehicles; three were confirmed as directly related to the engine failure, and nine reports described an under-hood fire that occurred following a loss of power event. Additionally, ODI identified multiple reports describing an engine block crack or hole surrounded by oil residue following an engine failure. On June 27, 2025, Nissan submitted recall 25V-437 involving 443,899 MY 2021-2023 Nissan Rogue, MY 2019-2021 Nissan Altima; MY 2019-2021 Infiniti QX50; and 2022 Infiniti QX55 vehicles. The recall remedy provides the dealer instructions to inspect the engine oil pan for the presence of specific metal debris. For customers with the 3-cylinder 1.5L VC-Turbo engine, if no debris is detected during the inspection, dealers will replace the oil pan gasket, engine oil, and reprogram the vehicle’s Engine Control Module (ECM). For customers with the 4-cylinder 2.0L VC-Turbo engine, if no debris is detected, dealers will replace the engine oil. In the case where specific debris is detected and confirmed by Nissan Powertrain Call Center, dealers will be instructed to replace the engine. In addition, Nissan will extend the vehicle warranty to 10 years and 120,000 miles for the recall subject vehicle population after the dealer performs the inspection. Nissan has implemented multiple corrective actions to address the identified manufacturing defects of certain engine block internal components.  In view of the recall action (25V437) taken by Nissan, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.

I currently own a 2020 Nissan Altima with 49,186 miles and I am reporting a recurring power door lock failure. This vehicle was inspected at the Nissan of Cumming location this morning to confirm the issue. Three of the passenger-side door lock actuators have failed within a short period of time. The two rear door locks stopped working at the same time, and approximately two weeks later the front passenger door lock also stopped working. The driver's door has started to not unlock when turning the car off where it normally did up until recently. The affected doors do not respond to the interior power lock/unlock buttons or the key fob. When attempting to lock or unlock the doors electronically, I can hear the actuators attempting to operate, but the doors do not actually lock or unlock. The doors can only be locked or unlocked manually. This failure affects multiple doors and appears to be a premature component failure given the vehicle's mileage. A malfunctioning power lock system could create a safety concern if occupants are unable to quickly secure or unlock doors during an emergency situation or if electronic access is needed. I am requesting that the NHTSA investigate whether there is a broader defect involving door lock actuators or the power door lock system in 2019 - 2020 Altima vehicles. I have also submitted a case with Nissan Affairs. The case number is 56942179.

NHTSA ID

11753776

Incident

Jul 30, 2026

When I am driving my car randomly states check engine and makes a beeping noise and then the engine starts to make some type of combustion noise and then slows down and then turns off.

NHTSA ID

11752874

Incident

Nov 12, 2025

Both passenger-side and driver's side rear door lock mechanisms ceased working. They do not work when attempting to lock/unlock the doors from the inside controls in the front seat. These doors also do not lock/unlock when using the remote key fob either. Both rear doors have to be lock/unlocked manually from the inside of the door.

NHTSA ID

11751528

Incident

Aug 1, 2025

The warming lights for different items come on at random. Examples :Low washer fluid, gas cap open, speedometer digital speed not showing.

NHTSA ID

11750677

Incident

Feb 18, 2026

The contact owns a 2020 Nissan Altima. The contact stated that the auto-braking system unexpectedly activated, and there was a grinding sound coming from the brakes; however, the vehicle failed to stop as needed. The ABS warning light was illuminated. While driving approximately 60 MPH, the brakes suddenly activated, and the instrument panel illuminated with a vertical yellow light. The vehicle was pulled over to the side of the road and waited for a while before restarting the vehicle to continue driving. The failure reoccurred the following morning while driving 35 MPH. There was no warning light illuminated. The vehicle was pulled over, turned off, and restarted to continue driving. The failure had occurred approximately 5 times. The contact stated that with the cruise control set to co-pilot, the steering and lane assist features failed to operate as intended, advising the contact to manually steer the vehicle. The failure became more persistent. The vehicle was not taken to the dealer. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 120,000.

NHTSA ID

11750330

Incident

Jul 12, 2026

Mileage

120,000 mi

Odometer Fraud. The contact purchased a 2020 Nissan Altima. The contact became aware that there was a mileage discrepancy after the purchase. The vehicle was an independent dealer sale. At the time of the purchase, the vehicle mileage was 83,000. It was later discovered during routine maintenance with an authorized local dealer that the mileage was 125,000.

NHTSA ID

11744494

Incident

Jun 16, 2026

Mileage

125,000 mi

All four of my door lock actuators have went out without warning. This has caused stress and frustration due to not having the correct access to get in and out of my vehicle. The doors would not lock or unlock by pressing the buttons on the door or on the key itself. This has also caused a big safety concern. Being able to not open my car door is dangerous and could potentially hurt myself or others. I have contacted Nissan and they stated that there were not any recalls on my vehicle but I was suspicious since all lock actuators went out around the same time frame. I have paid to get 3/4 lock actuators replaced out of my own pocket with 1 lock actuator still not fixed. I was not made aware of the lock actuators failing and didn’t know that this was a problem a lot of other people were experiencing as well.

NHTSA ID

11740834

Incident

Apr 1, 2026

This issue involves a documented and recurring safety-related defect that was reported multiple times while my vehicle was still covered under Nissan’s factory warranty related to the airbag system. My 2020 Nissan Altima currently has approximately 53,900 miles and has experienced repeated airbag/SRS failures associated with diagnostic code B1436-13, indicating an open circuit within the passenger airbag system. This issue has occurred on multiple occasions, including in 2022, 2024, 2025, and 2026. During several warranty-period service visits, the diagnostic codes were reportedly cleared, however, the underlying wiring harness issue does not appear to have been permanently corrected. I have the full history service record for this car with notes from 3 Nissan Dealers. I have documented communications with Nissan Consumer Affairs dating back to May 13, 2024 regarding this ongoing concern. In addition, I have photographic evidence showing the same airbag fault code on February 22, 2025, along with additional correspondence with Nissan dated March 18, 2025. Both of these events occurred while the vehicle remained within the applicable warranty coverage period. The airbag warning light has now returned again, and I have been presented with a repair estimate exceeding $5,200 for a condition that was previously reported and addressed unsuccessfully while the vehicle was under warranty coverage. According to Nissan’s 2020 Warranty Information Booklet, the Restraint System, including airbags and related electronic control systems, is covered under Nissan’s 5-year/60,000-mile warranty coverage. Because this safety concern was documented during the warranty period and prior repair attempts did not resolve the issue. Given that this matter involves a critical vehicle safety system that could affect passenger airbag deployment, I am hopeful this can be resolved.

NHTSA ID

11737675

Incident

May 1, 2026

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

TELEMATICS SERVICE INFORMATION HINT: This bulletin applies to vehicles equipped with a 4G network compatible TCU. TCUs compatible with 3G network only are no longer supported. SERVICE INFORMATION The APPLIED VEHICLES that come equipped with a factory installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active NissanConnect® Services subscription, the TCU communicates with the NissanConnect® Services Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. · A table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. · A CHECK-OFF SHEET has been provided on page 20 to print and check off steps as they are performed. Staple the completed CHECK-OFF SHEET to the repair order.

FALSE ACTIVATION OF AEB OR FCW IF YOU CONFIRM The customer states they have experienced false activation and/or unexpected braking of the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system, AND There are no related DTCs stored. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Confirm the current ICC/ADAS part number. 2. Reprogram the ICC/ADAS, if applicable. 3. Configure the ICC/ADAS. 4. Erase the DTCs. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual