2024 Nissan Altima

The contact owns a 2024 Nissan Altima. While driving for Uber, a customer alerted the contact of an abnormally strong odor in the rear seats of the vehicle. The contact later discovered that there was white mold inside the trunk of the vehicle and the spare tire compartment which was caused by the filament used to seal the liners in the trunk and rear seats. The contact was concerned about the health risk. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 80,000.

NHTSA ID

11755464

Incident

Aug 5, 2026

Mileage

80,000 mi

The contact owns a 2024 Nissan Altima. The contact stated that while entering the vehicle and closing the door, the rear windshield shattered spontaneously. The vehicle was towed to a dealer. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 7,893.

NHTSA ID

11750002

Incident

Jun 29, 2026

Mileage

7,893 mi

I came home to the glass shattered on the rear windshield of the car. It was buckled up but in pieces. Some of the class has been removed. If driving and this happened it could have caused an accident. Called dealer they said to file a case with Nissan

NHTSA ID

11741615

Incident

May 29, 2026

Component/System Failure: Front driver's seatback cover assembly (Nissan Part Number: 87650-9HB2B). The factory structural stitching on the center backrest panel is actively unraveling and separating. The component is available for inspection upon request. ​ Safety Risk: The seatback cover serves as the structural envelope for the Supplemental Restraint System (SRS) Side-Impact Airbag. Because the structural factory stitching has failed, the engineered tension of the airbag housing unit is compromised. A unravelling cover cannot ensure the precise breakaway path required for the side airbag to deploy correctly. This structural defect poses a severe safety liability, risking delayed deployment, non-deployment, or improper trajectory of a critical safety restraint during a collision. ​Inspections by Others & Dealer Confirmation: The physical separation of the stitching was presented to and verified by an authorized manufacturer dealership (Hubler Nissan) on April 21, 2026. The dealership acknowledged the physical failure of the stitching but refused to perform a factory-certified repair. Nissan's warranty claims the restraint system is covered for 60,000 miles, yet the dealership officially advised me to take the vehicle to a third-party, non-certified local shop ("Dr. Vinyl") to repair the structural housing of an active explosive device. This creates an unacceptable safety liability for both the vehicle occupants and Nissan. ​ Warning Lamps & Prior History: No active dashboard SRS warning lamps are illuminated, as the fault is a physical structural breakdown rather than an electrical failure. The issue first appeared prior to 36,000 miles and continues to progressively worsen.

NHTSA ID

11741526

Incident

Apr 21, 2026

When the vehicle is put in reverse, the screen for the rear camera goes completely blank. This is a known defect with many Nissan vehicles, to which Nissan has issued numerous recalls to address this exact issue. However, the year, make, and model of my vehicle has not been included in any of Nissan’s recalls.

NHTSA ID

11737880

Incident

Aug 1, 2025

The contact owns a 2024 Nissan Altima. The contact stated that while driving at 65 MPH, the contact received third-degree burns to the buttocks from the driver’s side seat warmer. The contact was in a wheelchair due to the burns, and medical attention was required. A dealer was contacted and requested to open the vehicle seats. The vehicle was not taken to an independent mechanic or dealer to be diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 15,073.

NHTSA ID

11731594

Incident

Apr 11, 2026

Mileage

15,073 mi

The contact owns a 2024 Nissan Altima. The contact stated that while her daughter was driving at undisclosed speeds, the brakes erroneously activated, and the vehicle felt as if it was sliding while driving in the rain. The Forward Collision Avoidance warning light was illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted, but no assistance was provided due to the address. The failure mileage was unknown.

NHTSA ID

11730742

Incident

Apr 6, 2026

The driver’s seat heater malfunctioned and produced excessive heat while activated during normal vehicle operation. The heat became extremely intense at a low temperature and resulted in burns to the driver’s midsection, lower back, and upper buttocks. I, the driver sustained physical injuries including burning sensations, skin irritation, and visible discoloration marks in the affected areas. The excessive heat occurred without warning and created a safety hazard to the driver while operating the vehicle. There were no warning lights, messages, or alerts indicating a problem with the seat heating system prior to the incident. The vehicle has not yet been inspected by Nissan Motor Corporation Consumer Affairs. An inspection appointment originally scheduled for February 24, 2026 was rescheduled to March 12, 2026. The vehicle and seat heating components are available for inspection upon request.

NHTSA ID

11723155

Incident

Jan 2, 2026

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

CAN COMMUNICATION CODES – DIAGNOSTIC TIPS AND GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.