2013 Nissan Altima

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

On July 29, 2019, the Office of Defects Investigation (ODI) opened EA19002 to investigate instances of alleged rear lower control arm failures in 2013-2018 Nissan Altima and 2016-2018 Nissan Maxima vehicles. At the time the investigation was opened ODI had 91 consumer complaints alleging rear lower control arm failures in the subject vehicles.ODI was concerned about these complaints because many of them alleged an increased steering effort or loss of vehicle control.At the time these complaints were received, ODI was also aware of a proactive service campaign addressing 2013 Nissan Altima in salt-belt states for a similar concern. Since opening the investigation, ODI has confirmed, based on consumer complaints, warranty data, and testing conducted by Nissan and ODI, that owners of the subject vehicles are experiencing a corroded bushing at one of three mounting points of the control arm to the rear subframe.ODI has also confirmed that drivers become aware of the problem because of sound and abnormal vibrations. In addition, the failure mileage is typically over 113,000 miles at the time of failure.In conjunction with Nissan and VRTC, ODI participated in testing to assess the potential safety consequence of a bushing failure.It was found the Vehicle Dynamic Control system allows the driver to maintain vehicle control in the event of a bushing failure.With between 7 to 13 years of field exposure, ODI is aware of only one low speed crash allegation describing minor contact with another vehicle’s trailer hitch. Nissan acknowledges that a crack can develop in affected control arms due to stress loading from normal use and that salts commonly used for roadway snow and ice treatment may result in corrosion that exacerbates the progression of the crack.Nissan implemented a design change in January of 2018 to improve the durability of the lower control arm.Affected vehicles have either been repaired with the countermeasure part under a customer satisfaction campaign or been provided a warranty extension from 3 years/36,000 miles to 10 year/unlimited mileage. Through testing and analysis of the information obtained to date, ODI has not identified a defect representing an unreasonable risk to motor vehicle safety involving corrosion of the subject rear lower control arm at this time.With a declining trend of reports and Nissan’s actions to implement a countermeasure and extended warranty coverage, further investigation of the issue does not appear to be warranted at this time.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov. A detailed discussion of the investigation and related complaint numbers can be viewed in the attached closing report.

PE18-013 was opened on December 1, 2018, with 4 complaints to ODI alleging incidents of the lower control arm fracturing at a connection point to the vehicle chassis due to corrosion. ODI has received an additional 87 complaints since the PE was opened. During PE18-013, Nissan indicated model years 2013-2018 shared a common rear lower control arm design. Nissan provided complaint and warranty data regarding 48 incidents of the subject failure. The majority of the complaints are from vehicles registered in salt belt states. There have been no crashes, injuries, or fatalities confirmed as of this date. Nissan advised that it has conducted testing to assess safety risk. Nissan states that due to low incident rate, high detectability, and low risk of adverse vehicle dynamics, it does not believe the subject lower control arm failure poses an unreasonable risk to motor vehicle safety.This preliminary evaluation has been upgraded to Engineering Analysis (EA) 19-002. During the EA, ODI will continue to collect and analyze complaint and field data in its efforts to fully assess the scope and frequency of the alleged defect. More importantly, ODI will also seek additional information and data regarding the potential safety consequences of rear lower control arm failure, both from evidence collected from field failures and through more rigorous and comprehensive vehicle testing to be conducted by either Nissan and/or NHTSA.The ODI reports (VOQs) cited above can be viewed at NHTSA.gov under the following reference numbers: 11234334, 11234232, 11234189, 11233771, 11233234, 11232381, 11231589, 11230323, 11230184, 11229023, 11229003, 11228730, 11228651, 11228631, 11228625, 11223086, 11222602, 11222427, 11222303, 11221802, 11219943, 11217980, 11217542, 11217505, 11217290, 11210699, 11209647, 11208580, 11208274, 11207545, 11206310, 11205711, 11205461, 11203864, 11203005, 11195416, 11193545, 11193020, 11192269, 11192066, 11191270, 11191207, 11191185, 11191042, 11190360, 11190323, 11187334, 11187157, 11186747, 11186195, 11185664, 11185632, 11185589, 11183799, 11183295, 11183198, 11182705,11182528, 11182265, 11182137, 11182088, 11181373, 11181223, 11181155, 11181009, 11180126, 11176565, 11176261, 11176135, 11175821, 11172604, 11172200, 11172065, 11170019, 11169930, 11165194, 11163833, 11163489, 11162559, 11162195, 11161956, 11161497, 11161117, 11157323, 11157234, 11156772, 11141169, 11139516, 11129476, 11122829, 11114374.

In May 2016, Nissan North America issued a safety recall (16V-244) to address the problem of improper classification of adult front seat passengers in approximately 3.3 million vehicles, including those in the scope of this investigation when it was opened (almost one million vehicles) and additional vehicles, as shown below.Nissan models: certain model year 2013-2016 Altima, 2013-2016 LEAF, 2016-2017 Maxima, 2015-016 Murano and Murano Hybrid, 2013-2016 Pathfinder, 2014-2015 Pathfinder Hybrid, 2014-2017 Rogue, 2013-2016 Sentra, 2013-2016 NV200, and 2014-2016 Taxi.Infiniti models: certain model year 2013 JX35, 2014-2017 Q50, 2014-2016 Q50 Hybrid, and 2014-2016 QX60 and QX60 Hybrid.Chevrolet model: certain model year 2015-2016 City Express.Additional information on the above-referenced recalls is available online at NHTSA.gov.Also, the numbers shown in the above failure report summary are for the original vehicle population, as opposed to the entire recall population, and the ODI reports cited are as of May 31, 2016 when Nissan began to notify the affected owners of recall 16V-244.Based on the recall actions taken by Nissan, this Engineering Analysis is closed.Additional information on this closing resume and the investigation are in the EA15-004 public file available online at NHTSA.gov.The ODI reports cited above can be reviewed online at https://www.nhtsa.gov/recalls#vehicle under the following identification numbers: 10583283 10585264 10585349 10585379 10592434 10593399 10593501 10594329 10594614 10594755 10595161 10595645 10595946 10596128 10596459 10596952 10597037 10597452 10597518 10597719 10598537 10598869 10604755 10604834 10605188 10605251 10606565 10606828 10607038 10609649 10610519 10610991 10614467 10614609 10614745 10616905 10617008 10617507 10617903 10618099 10618202 10619059 10619563 10620719 10621840 10622214 10625808 10625981 10625998 10626006 10626023 10626335 10626458 10626732 10628355 10629382 10629460 10629606 10630441 10630502 10630990 10632251 10632588 10632934 10632997 10633714 10633810 10637994 10638591 10639040 10639147 10639324 10639473 10643046 10643843 10644203 10644333 10644341 10644690 10644891 10644985 10648834 10648997 10649414 10649772 10649874 10651360 10651564 10651924 10651982 10652024 10658665 10658844 10659484 10660294 10661195 10661358 10661541 10661795 10661855 10662901 10663033 10663338 10663860 10663978 10668054 10668768 10670538 10672807 10673088 10676471 10678478 10678997 10679512 10680748 10680769 10680975 10681656 10682235 10682902 10682993 10683391 10683689 10689672 10689809 10689981 10691626 10692137 10692558 10692625 10693168 10695312 10700614 10700960 10701008 10701011 10701014 10701018 10701023 10701027 10701031 10701032 10701035 10701045 10701055 10701064 10701074 10701146 10701196 10701228 10701237 10701254 10701301 10701306 10701326 10701367 10701370 10701384 10701415 10701453 10701526 10701558 10701656 10701670 10701946 10702003 10702667 10702798 10703032 10703657 10703766 10703813 10704196 10704988 10705530 10705919 10706621 10712543 10712568 10712575 10713335 10714316 10714330 10714536 10714980 10715132 10715945 10717336 10720918 10720971 10721331 10721746 10723424 10724568 10731167 10731868 10732012 10732065 10733877 10735438 10745948 10745982 10746399 10747660 10748077 10749091 10749110 10758979 10761398 10761433 10763320 10764590 10766486 10775946 10777923 10779712 10781422 10781449 10781508 10781901 10783624 10783776 10785993 10786461 10786713 10786788 10787867 10788370 10788371 10788962 10789694 10790181 10790230 10790362 10794790 10806647 10806933 10807302 10807841 10810487 10810558 10811858 10811864 10816502 10816686 10818702 10820204 10821247 10821751

The headlight housings metallic coatings for reflectivity are failing and reduce the efficacy of the headlights. There has been a class action lawsuit against Nissan for this but many, like myself, were not notified. The headlights are very dim and create a safety hazzard when driving in an area where high beams can't be used. NTSHA really needs to do what is right here and force a recall.

NHTSA ID

11754115

Incident

Oct 1, 2024

Front passenger door lock actuator fails to unlock door when driver's, passengers or key fob to unlock is activated. All other doors (3) work as they should. This creates a safety issue as the door must manually be unlocked which during a panic situation may not be easily accomplished. I am in the process of having the mechanism inspected & repaired. Part failed with no notice. It may have failed earlier, but July '26 was the 1st I noticed.

NHTSA ID

11754114

Incident

Jul 5, 2026

Rear left wheel busted off of car while driving. Flew up into the back end of car totaling the vehicle. We were very lucky no one was hurt.

NHTSA ID

11751642

Incident

Jun 11, 2026

The contact's friend owns a 2013 Nissan Altima. The contact stated that when the vehicle was parked, the check engine warning light illuminated and remained illuminated for an extended period. The vehicle was taken to two independent mechanic shops, where it was diagnosed that the catalytic converter needed to be replaced; however, the vehicle was not repaired. The vehicle was then taken to a dealer, where the check engine warning light was no longer illuminated, and the failure could not be replicated. The manufacturer was not notified of the failure. The failure mileage was approximately 92,000.

NHTSA ID

11749375

Incident

Mar 15, 2024

Mileage

92,000 mi

Headlights are extremely dim almost always have to drive with my high beams on at night since the lights are so dark. Have tried replacing bulbs on my own but lights are still dim. No warning or anything were ever shown

NHTSA ID

11743107

Incident

Jun 1, 2022

The car feels unbalanced and shifting is bad

NHTSA ID

11729811

Incident

Jan 14, 2026

The contact owns a 2013 Nissan Altima. The contact stated that while attempting to accelerate from a stop sign, the vehicle accelerated to approximately 15 MPH and then unexpectedly decelerated. The contact attempted to depress the accelerator; however, the vehicle lost automotive power and stalled. The vehicle was towed to the residence. There were no warning lights illuminated. The vehicle was taken to the dealer to be diagnosed. The contact was informed that the transmission needed to be repaired. The vehicle was not yet repaired. The manufacturer was informed of the failure and confirmed that the VIN was not under recall. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 100,000.

NHTSA ID

11727165

Incident

Jun 26, 2025

Mileage

100,000 mi

The vehicle is a Nissan Altima experiencing a low-beam headlight failure. The headlights have become extremely dim and no longer provide adequate illumination of the roadway at night. Visibility is severely reduced, making it difficult to see lane markings, pedestrians, and obstacles ahead. The vehicle and headlight assemblies are available for inspection upon request. This condition creates a serious safety risk because nighttime driving visibility is significantly compromised. The headlights are so dim that safe operation of the vehicle after dark is difficult, increasing the risk of a crash involving pedestrians, other vehicles, or road hazards. The vehicle was inspected by a Nissan dealership, which confirmed the headlight problem. However, the dealer has refused to repair the issue under the applicable safety recall due to a missed deadline (March 2022). We first became aware of the recall in March 2023 and have been attempting to resolve the issue since that time. The vehicle has been inspected by the dealership but has not been inspected by police or insurance representatives. There were no warning lights, dashboard messages, or other alerts indicating a headlight system problem prior to the failure. The primary symptom has been the gradual dimming of the low-beam headlights over time until they became too dim to safely illuminate the road.

NHTSA ID

11724404

Incident

Mar 1, 2026

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

CVT/TCM CALIBRATION DATA “WRITE” PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.