2005 Chrysler 300

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

The Office of Defects Investigation (ODI) opened PE14-016 in June 2014 based on six inflator rupture incidents involving consumer owned vehicles produced by five vehicle manufacturers.All six vehicles were operated in Florida or Puerto Rico at the time of the rupture and for the majority of their service life, and were equipped with inflators produced by Takata, a tier-one supplier of automotive air bag systems.During the course of PE14-016, ODI determined that five additional vehicle manufacturers used inflators of a similar design and vintage also supplied by Takata. No evidence of field failures was found in vehicles produced by these five additional manufacturers.Nonetheless, at ODI's insistence, all 10 vehicle manufacturers initiated a regional recall within approximately two weeks of the opening of the investigation.The regions recalled initially included Florida, Puerto Rico, Hawaii, and the U.S. Virgin Islands, areas with high absolute humidity and climatic conditions believed to be a significant factor in the inflator ruptures.As part of the recall actions, inflators removed from remedied vehicles are to be returned to Takata for testing.Takata's initial test results on passenger inflators from remedied vehicles indicated a much higher than anticipated rupture frequency for inflators returned from Florida.Accordingly ODI requested all 10 manufacturers expand the regional recalls for passenger inflators to include other geographic areas where high absolute humidity conditions exist, including the Gulf States and other coastal areas.Takata's testing of the passenger inflators to date continues to indicate this geographic area as having the highest risk, with no ruptures occurring from inflators returned from outside the expanded recall regions.During PE14-016 four additional passenger inflator field events occurred, all in vehicles from the same expanded geographic region.Also during PE14-016 four additional driver inflator field events occurred including two in vehicles from regions not known for high absolute humidity, specifically California and North Carolina.Accordingly, ODI requested all five of the affected vehicle manufacturers currently using the subject Takata driver inflators expand to nationwide recalls.Significantly, neither of the affected vehicle manufacturers or Takata provided any explanation to account for these two driver air bag inflator ruptures outside the area of high absolute humidity.Takata testing of returned driver inflators indicates a lower rupture frequency as compared to passenger inflator testing.All test ruptures reported by Takata to date have occurred on inflators returned from high absolute humidity areas.The investigation now includes all manufacturers and vehicles known to be affected at this time.ODI's investigation will focus on, among other things, root cause analysis, other potential defect consequences, identification of affected vehicles scope, and adequacy of the remedy.The five ODI reports cited above can be reviewed online at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10537899, 10568848, 10585224, 10605877, 10651492

The Office of Defects Investigation (ODI) opened PE14-016 in June 2014 based on six inflator rupture incidents involving consumer owned vehicles produced by five vehicle manufacturers.All six vehicles were operated in Florida or Puerto Rico at the time of the rupture and for the majority of their service life, and were equipped with inflators produced by Takata, a tier-one supplier of automotive air bag systems.During the course of PE14-016, ODI determined that five additional vehicle manufacturers used inflators of a similar design and vintage also supplied by Takata. No evidence of field failures was found in vehicles produced by these five additional manufacturers.Nonetheless, at ODI's insistence, all 10 vehicle manufacturers initiated a regional recall within approximately two weeks of the opening of the investigation.The regions recalled initially included Florida, Puerto Rico, Hawaii, and the U.S. Virgin Islands, areas with consistently high absolute humidity and climatic conditions believed to be a significant factor in the inflator ruptures.As part of the recall actions, inflators removed from remedied vehicles are to be returned to Takata for testing.Takata's initial test results on passenger inflators from remedied vehicles indicated a much higher than anticipated rupture frequency for inflators returned from Florida.Accordingly, ODI requested all 10 manufacturers expand the regional recalls for passenger inflators to include other geographic areas where high absolute humidity conditions exist, including the Gulf States and other coastal areas.Takata's testing of the passenger inflators to date continues to indicate this geographic area as having the highest risk, with no ruptures occurring from inflators returned from outside the expanded recall regions.During PE14-016, four additional passenger inflator field events occurred, all in vehicles from the same expanded geographic region.Also during PE14-016, four additional driver inflator field events occurred including two in vehicles from regions not known for high absolute humidity, specifically California and North Carolina.Accordingly, ODI requested all five of the affected vehicle manufacturers currently using the subject Takata driver inflators expand to nationwide recalls.Significantly, neither of the affected vehicle manufacturers or Takata provided any explanation to account for these two driver air bag inflator ruptures outside the area of high absolute humidity.Takata testing of returned driver inflators indicates a lower rupture frequency as compared to passenger inflator testing.All test ruptures reported by Takata to date have occurred on inflators returned from high absolute humidity areas.The PE is now closed/upgraded to an Engineering Evaluation (EA15-001) to include all manufacturersand vehicles known to be affected at this time.ODI's EA investigation will focus on, among other things, root cause analysis, other potential defect consequences, identification of affected vehicles scope, and adequacy of the remedy.The recalls related to this PE are: 14V343, 14V344, 14V348, 14V351, 14V353, 14V655, 14V700, 14V701, 14V752, 14V763, 14V770, 14V773, 14V787, 14V802 and 14V817.The number of vehicles affected are an estimate since some vehicles may have both the driver and passenger side inflators recalled. The five ODI reports cited above can be reviewed online at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10537899, 10568848, 10585224, 10605877, 10651492

The contact owns a 2005 Chrysler 300. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 16V352000 (Air Bags); however, after retrieving the vehicle the following day, the vehicle experienced several failures while driving. The A/C was inoperable, the vehicle was running rough, the check engine warning light was flashing, and the vehicle almost stalled while coming to a stop. Additionally, the contact became aware that there was a hole in the fuel tank. The dealer was notified of the failures, but no assistance was provided. The manufacturer was notified of the failure, and a case was filed. The manufacturer followed up with the dealer, and the contact was later informed that no assistance would be provided because the failures were unrelated to the recall, as per the dealer’s assessment. The vehicle was not diagnosed or repaired. The failure mileage was approximately 106,272.

NHTSA ID

11731463

Incident

Mar 31, 2026

Mileage

106,272 mi

This is a serious safety concern regarding the shift interlock system on my 2005 Chrysler 300. When the vehicle is in Park, particularly in traffic, and the light turns green, I am forced to lift the coin attachment and manually press the pink interlock just to change gears or accelerate. This creates a dangerous situation where I am unable to move the vehicle promptly, potentially leaving me vulnerable to a rear-end collision. The issue stems from Recall 05V462000, which specifically addresses a shift interlock defect that Chrysler has failed to address despite my repeated attempts to have it repaired. Chrysler has not taken any action to resolve the recall issue, leaving me in a potentially life-threatening situation every time I drive. It is unacceptable that this recall has not been acted upon, and this critical safety defect must be corrected immediately.

NHTSA ID

11624858

Incident

Nov 5, 2023

The vehicle began to shutter in reverse. This went on for about a week. Transmission fluid level was checked and it was in the normal range. My husband and I were driving it and made a sharp turn to find us in a spot to continue forward and go off a cliff or back up and get out of traffics way. He backed up and we heard a clunk. The car continues to drive forward with no issues but it acts as of it’s in neutral when you put it in reverse. No codes are showing either.

NHTSA ID

11604911

Incident

May 19, 2024

my engine blew, transmission is slipping. I’m having electrical and air bag problems.

NHTSA ID

11512289

Incident

Oct 31, 2022

The contact owns a 2005 Chrysler 300. The contact stated while starting the vehicle, the front passenger’s side air bag warning light illuminated. The vehicle was not taken to the dealer to be diagnosed or repaired. The manufacturer was contacted and stated there was no recall for the failure. The failure mileage was 19,641.

NHTSA ID

11498307

Incident

Dec 20, 2021

Mileage

19,641 mi

Strong fuel smell in cabin and outside of car when gas tank is full. Discovered gas in the cabin sitting on top of the fuel tank under the passenger-rear seat. Multiple posts in online forums confirm this is a known issue. Vehicle owner ordered a new o-ring to attempt repair. Area around fuel pump under driver's-rear seat was not affected. No warning lights, notices or performance issues. Only indication is strong gas fumes in car after filling up the gas tank (auto shutoff at pump, not topped off) which persists for several days. Problem seems minimized if gas tank is shorted 2-3 gallons from max capacity on fillup (about 14 gallons when car is close to empty per the gas gauge in dashboard.) Car was not inspected by dealer, insurance agent, police, independent service center, or anyone else other than owner.

NHTSA ID

11495459

Incident

Jun 1, 2022

The contact owns a 2005 Chrysler 300. The contact stated that while the mother was driving at approximately 10 mph when suddenly the driver-side air bag erroneously deployed. During the incident, no crash had occurred and the vehicle had not driven over a pothole or bump in the road. The driver sustained a left-hand injury which included three fractured fingers. The local dealer and manufacturer were notified of the failure. The vehicle was towed away and examined by the manufacturer's engineer. The cause of the failure was not explained but the contact was informed that the manufacturer took no responsibility for the failure. The vehicle was not repaired. The failure mileage was 190,000

NHTSA ID

11487307

Incident

Jun 14, 2022

Mileage

190,000 mi

The contact's mother owns a 2005 Chrysler 300. The contact stated that while her mother was driving approximately 10 mph, the air bag deployed without a crash or impact. The driver sustained a fractured finger and medical attention was provided. The contact called the local dealer but the vehicle was not diagnosed or repaired. The contact stated the failure was due to NHTSA Campaign Number: 15V313000 (Air Bags). The manufacturer was notified but no additional assistance was provided. The approximate failure mileage was 190,366.

NHTSA ID

11478250

Incident

Jun 14, 2022

Mileage

190,366 mi

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission