2008 Chrysler 300

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

I informed the dealership of ignition switch recall shortly after purchasing vehicle. The dealership stated " the VIN number shows no recalls". And that was it said there nothing showing up. I KNOW ignition switch is messed up because every time I would turn the car off I could still feel it running. I've had my car a year and now it will not crank due to ignition switch and now fuel air intake is also messing up and has caused cylinder 6 to miss fire. I have been without a vehicle for a month now and I need it fixed. When test driving the car, it would slow down as I was turning into a place of business and almost getting hit by another vehicle.

NHTSA ID

11703857

Incident

Nov 26, 2024

The contact owns a 2008 Chrysler 300. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 14V567000 (Electrical System); however, the repair failed to prevent a failure from occurring. The contact stated that several days after the recall repair was completed, the contact had to adjust the ignition switch to start the vehicle. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 68,000.

NHTSA ID

11700171

Incident

Nov 18, 2025

Mileage

68,000 mi

When taking vehicle for test drive about a month ago, the check engine light was on and after driving it, i noticed when AC was on and when off, the car loses power. When i go to pull out it has no power and i almost got hit in the side every time i would pull out from a busy highway. They had check engine light looked at and they said computer told them it was air valve leak or something like that. I had appointment for them to further assist and they said they could not find anything wrong. I can hear where the valve might be leaking at. The brakes are not good. I had to put on the brakes today fast and brake pedal acted like they were gonna skid out from under my foot. Brakes are new so why is it acting like i have no brakes and there is barley any acceleration. Something is going on and i don't want to be in a car accident just because our warnings are being over looked.

NHTSA ID

11626365

Incident

Nov 10, 2024

The contact owns a 2008 Chrysler 300. The contact received notification of NHTSA Campaign Number: 16V352000 (Air Bags) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.

NHTSA ID

11566323

Incident

Jan 18, 2024

Dealer is unable to order the recalled air bag. I had it in to be fixed a month ago, verified with dealer they had the part before I made the appointment. Took it in and they advised it is on backorder. Called 1q/10 and they advised they are NOT ALLOWED to order the part. What am I supposed to do?

NHTSA ID

11493259

Incident

Oct 18, 2022

I don't know what had happened I was driving one day and my air bag light came on and it stayed on. Never been in a accident since I got the car had it since 2021

NHTSA ID

11485964

Incident

Aug 11, 2022

HAIR LIKE CRACKS ABOVE FUEL PUMP! CONSTANTLY LEAKING GAS N CAR STALLING OUT!!!

NHTSA ID

11404277

Incident

Mar 4, 2021

Mileage

151,000 mi

FOR THE AXLE OR THE WHEEL BEARINGS OR SOMETHING LIKE THAT EVERY TIME I TURN THE WHEEL TO A CERTAIN ANGLE IT POPS ALSO HAS HARD VIBRATION WHILE DRIVING THE BUTTONS HAVE FALLEN OFF THE SEATS THE STEERING PULLS TO THE RIGHT HAS RUST BY THE GAS TANK 0102 SINCE BANKS SENSORS HAVE ONE OUT AND HAS STOPPED STARTING OCCASIONALLY HAVE REPLACED KEY FOB BUT IT OCCASIONALLY STILL HAPPENS AND THE FLOW SENSOR ALERT IS COMING ON FOR THE CODE AIRBAG RECALL NEEDS DONE THE WHEELS PRESSURE SENSOR GAUGE NEVER TURNS OFF FOR THE ALERT I'VE HAD TO HAVE MY CAR TOWED THREE TIMES BECAUSE I'M NON-START AND ENGINE LIGHT IS STILL ON ALSO DANGEROUSLY THE HEAT SHIELD HAD COME APART ON MY CAR JUST RECENTLY 2020 SUPER DANGEROUS WHILE DRIVING

NHTSA ID

11373074

Incident

Dec 12, 2019

Mileage

200,000 mi

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission