2018 Ford E350

TL* THE CONSUMER OWNS A 2018 FORD E-350. THE CONSUMER STATED THAT WHILE TRAVELING AT A LOW RATE OF SPEED, THE CONSUMER ATTEMPTED TO STOP THE VEHICLE BY DEPRESSING THE BRAKE PEDAL; HOWEVER THE VEHICLE FAILED TO OPERATE AS NEEDED. THE VEHICLE INSTEAD ACCELERATE FORWARD WHILE TRAVELING APPROXIMATELY 30 MPH. THE VEHICLE WENT INTO AN EMBANKMENT, DID NOT COLLIDE OR HIT ANYTHING, NO FRONT END DAMAGE, HOWEVER THE REAR OF THE VEHICLE WAS DAMAGED. THE AIR BAGS DID NOT DEPLOY DUE TO NO COLLISION, A POLICE REPORT WAS FILED(BR-19-13326). THE CONTACT WAS TAKEN TO A LOCAL HOSPITAL AND SUSTAINED A FRACTURED BACK. THE CAUSE OF THE VEHICLE FAILURE WAS UNKNOWN. THE VEHICLE WAS TOWED TO A LOCAL BODY SHOP AND THEN TO A DEALER(TRI-LAKES MOTORS 180 STATE HIGHWAY F, BRANSON, MO 65616 417-334-7543). VIN NUMBER WAS UNAVAILABLE TO SEARCH IF THERE WAS A RECALL PLACED ON THE VEHICLE. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 4,200. *BF *AS

NHTSA ID

11254747

Incident

Aug 8, 2019

Mileage

4,200 mi

THIS VEHICLE HAS A 12,500 GVWR. WE RECENTLY HAD THIS AT A FORD DEALER FOR A BROKEN LEFT REAR SUSPENSION. THE DEALER WEIGHED THE ENTIRE VEHICLE AND DETERMINED THE TARE WEIGHT TO BE 11,200 LBS. THIS IS A CLASS-C MOTORHOME AND IT WAS COMPLETELY EMPTY OF ANY AND ALL CARGO, NO LIQUIDS, WHICH IS CAPABLE OF CARRYING 40 GALLONS OF WATER AT 8.3 GALLONS PER POUND. THERE WAS LESS THAN 1/4 OF A TANK OF FUEL, OF A 55 GALLON TANK AND THE MANUFACTURER STATES THAT THIS IS A 4 PASSENGER VEHICLE. WITH THE MATH WE HAVE DONE, OF 40 GALLONS OF WATER AT 333.60 LBS AND 55 GALLONS OF GAS EQUATES TO 346.50 LBS. MY 4 MEMBERS OF MY FAMILY COMBINED WEIGH IN AT 800 LBS AND WITH ALL THE TOTALS ADDED TOGETHER I COME UP WITH 12, 680 GVWR. THIS VEHICLE HAS A RATED BY THE MANUFACTURER TOW CAPACITY OF 8,000 LBS. THE VEHICLE HAS MANY LARGE STORAGE BINS INCORPORATED INTO THE UNIT. BASED ON THE WEIGHTS DISPLAYED, I'VE ALREADY EXCEEDED THE GVWR. WITH THAT SAID, I CAN NOT LEGALLY DRIVE THIS VEHICLE WITH THE 4 MEMBERS OF MY FAMILY. MY STORAGE COMPARTMENTS ARE COMPLETELY EMPTY AND I HAVE NO CAMPING SUPPLIES ONBOARD, THAT INCLUDING POTS, PANS, CUPS, TOITLETRIES, CHAIRS, ETC.THE REASON FOR THIS NOTICE IS BECAUSE THE LEFT REAR SUSPENSION HAS FAILED IN ONLY 7,000 MILES TRAVELED. I'M FEARFUL THAT IF I DRIVE THIS AND HAVE ANY SITUATION ON THE ROAD, THAT MY INSURANCE COMPANY WILL INVALIDATE MY POLICY.

NHTSA ID

11185577

Incident

May 15, 2018

I WAS MAKING A 3 POINT TURN, AND WHEN I PUT THE TRUCK INTO REVERSE IT JUMPED FORWARD INSTEAD OF GOING BACKWARD, CAUSING THE VEHICLE TO STRIKE POWER POLE CABLES.

NHTSA ID

11083591

Incident

Apr 4, 2018

Mileage

4,800 mi

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.