2011 Ford Edge

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Brake Booster All of a sudden my brake went to the floor and made a hissing sound, spongy response. Took it to Cowin Ford and they diagnosed and replaced the brake booster. It was really dangerous as response to brake was really slow. I almost hit a car in front of me. No warnings or symptoms prior.

NHTSA ID

11747018

Incident

Mar 17, 2023

Brake Booster Was exiting the freeway so already slowed but it was a curvy off-ramp, thankfully no one was close and the car was already slowed, but on hazards and coasted home at 5 mph. Huge safety concern Tow truck towed to HTS Automotive to determine the brake booster went out, which we already knew as the same thing happened in 2023! No warnings, no symptoms prior

NHTSA ID

11747017

Incident

Sep 2, 2025

Break Booster Break fell to the floor, slow to stop, spongy. I was able to put on my hazards and roll to safety stop. Huge risk if I was going faster or turning a curve. Dangerous to me and others to not being able to stop The problem hasn’t been taken to the shop yet as it was closed and I had the same problem in 2025 and 2023 which were confirmed and fixed with ford parts. I am suspecting it is the same issue. Even if replaced the car is likely not safe wi the this part failing 3 times in less than 4 years. No warnings or symptoms, just falls to the floor and spongy break reaction

NHTSA ID

11747014

Incident

Jun 27, 2026

The contact owns a 2011 Ford Edge. The contact stated that while reversing out of the garage and depressing the brake pedal, the vehicle failed to immediately stop. The brake pedal was spongy. The contact stated that later, while driving at an undisclosed speed and depressing the brake pedal to stop the vehicle, the braking distance was extended. The vehicle was slowly driven to the local mechanic, who diagnosed that the brake booster had failed and needed to be replaced. The vehicle was not yet repaired. The local dealer was contacted. The manufacturer was not contacted or notified of the failure. The failure mileage was 110,000.

NHTSA ID

11746227

Incident

Sep 20, 2025

Mileage

110,000 mi

The brake pedal sunk all the way to the floor before braking. This has happened multiple times and now there is a leak in the ABS which we are in need of a ABS pump. Was told by mechanic that this is an ongoing problem with the Ford Edges. And, the real problem is the mechanic cannot find a replacement pump for it. Multiple locations were contacted but nothing is available. My Edge is a 2011 and currently has 84,500 miles. It’s a dangerous situation when the pedal sinks to the floor before stopping. There are no ABS warnings that pop up on the dash. Need to know what Ford is doing about this.

NHTSA ID

11734982

Incident

Apr 30, 2024

The throttle body issues again with the burning smell as well the whole car shut down like the other two times I reported on this website! Please note the team who fixed it last time was at Poway Ford and the main manager from auto maintenance was fired due to attempting to correct the issue on my 2011 Ford Edge!

NHTSA ID

11734578

Incident

Apr 29, 2026

The brake pedal does not feel right and the car continues to roll. My mechanic found that the brake pedal vacuum boosters commonly fail on this model. He repaired it and less than a year later it has failed again. I heard the air leak when pressing the pedal and the car does not stop, it continues to roll. I've had to park it because this is a safety issue. I do not want to risk my life or cause property damage. The car has less than 130,000 miles on it and no warning lights or messages come on the dash for this. This repair was over $600 but the manufacturer should fix this and make sure it's right and safe.

NHTSA ID

11734138

Incident

Apr 22, 2026

The contact owns a 2011 Ford Edge. The contact stated that while driving 10 MPH and coming to a stop, the brake pedal was depressed, but the vehicle failed to respond as intended. There was no warning light illuminated. The dealer was notified of the failure and provided an estimate for the repair. The vehicle was taken to an independent mechanic, where it was diagnosed with brake master cylinder failure. The vehicle was repaired; however, the failure recurred. The vehicle was not repaired a second time. The manufacturer was not notified of the failure. The failure mileage was approximately 105,000.

NHTSA ID

11732511

Incident

Apr 20, 2026

Mileage

105,000 mi

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

Certain 2010-2014 Model Year Edge and MKX Vehicles - Extended Warranty Coverage on Brake Booster

Certain 2010-2014 Model Year Edge and MKX Vehicles - Extended Warranty Coverage on Brake Booster

For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.

This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.