2008 Jeep Wrangler

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.

In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.

In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den

"On March 4, 2022, Customer Satisfaction Notification S33 (Airbag Clockspring Recall Remedy) was performed on my 2008 Jeep Wrangler by an authorized dealer at 123,314 miles. The vehicle now has 137, 347 miles. The replacement clockspring provided as the official safety remedy has completely failed after only roughly 15,000 miles of driving, illuminating the SRS airbag warning light and completely disabling the supplemental restraint system. The manufacturer's mandated remedy has failed to permanently correct the safety defect, creating a recurring hazard." Tom O'Brian dealership and Stellanis have both refused to repair clockspring which is either defective repair item. "Stellantis corporate directed me to speak with you directly regarding a safety component failure. Tom O’Brien Jeep performed the S33 clockspring campaign on my Wrangler at 123,314 miles. The vehicle only has about 138,000 miles on it now. This critical airbag safety component failed after just 15,000 miles of driving. Corporate told me that if you submit a Digital Goodwill Claim through the dealer portal for an internal part failure on a safety campaign, they can review it for approval. Because this disables my entire airbag system after only 15,000 miles, I am asking you to submit that goodwill request so Stellantis can cover the replacement." ," no federal safety regulator or corporate executive expects a vital component of a vehicle's supplemental restraint/airbag system to fail after just 15,000 miles. This extremely low mileage proves one of two things: either the replacement remedy part was defective out of the box, or the "dust shroud" modification required by the S33 campaign was not installed correctly, allowing the new clockspring to fail prematurely.

NHTSA ID

11750351

Incident

Jul 14, 2026

Odometer rollback and was not aware until yesterday.

NHTSA ID

11743678

Incident

Sep 17, 2022

ABS systems not functioning properly, showing engine code U0121 that states lost communication with ABS module. This is a common occurrence with jeeps and is a safety issue due to the abs system not working properly. Also causes the brakes to randomly engage and disengage.

NHTSA ID

11735712

Incident

Dec 29, 2025

While driving at speed, vehicle electrical went haywire. Headlights went on and off. Horn sounding on and off, Wipers and washers going on and off, HVAC blower on and off. Pulled over vehicle and turned off and removed key and it still remained running, all horn, lights, and wipers still going on and off. Opened hood, removed negative battery terminal, and with that, car still ran! Was several minutes and car finally shut itself off. Scary that the car went completely haywire and would not shut off, even with key out, and battery disconnected!

NHTSA ID

11704890

Incident

Dec 13, 2025

The ABS computer brake module is bad in my jeep. It needs a replacement. Confirmed by Chrysler Jeep dealership. However, Chrysler does not offer a replacement module. ABS does not work on my vehicle. This is a huge safety issue and is common problem among this year Jeep. Chrysler shouldn’t be allowed to NOT have a replacement OEM ABS module. Huge safety risk and lawsuit

NHTSA ID

11689603

Incident

Sep 25, 2025

ABS control module has gone out

NHTSA ID

11680650

Incident

Dec 31, 1969

I turned the key to turn on my car and the airbag deployed.

NHTSA ID

11674926

Incident

Jul 21, 2025

I was driving down the road in my 2008 wrangler and all of the sudden every light flashed on my dash board then it felt like I could not shift gears then smoke came pouring out of my air vents. I pulled over and got out realizing it was on fire. Climbed in to save my dog just before the fire got huge. My entire Jeep is gone.

NHTSA ID

11671473

Incident

Jul 1, 2025

SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

ACTUATOR - A/C AND HEATER

ACTUATOR - A/C AND HEATER

Plate - Planetary