2007 Jeep Wrangler

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.

In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.

In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den

The contact owns a 2007 Jeep Wrangler. The contact stated while attempting to start the vehicle, the brake pedal was depressed, however the brake pedal failed to function as intended. The contact stated that the brake pedal was depressed to the floor, and the service brakes failed to engage. The contact inspected the vehicle and noticed a hole in the brake line. In addition, the brake fluid was squirting out of the brake fluid canister. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 100,000.

NHTSA ID

11740132

Incident

May 23, 2026

Mileage

100,000 mi

i was driving my truck on Saturday march 21,2026 and all of a sudden black smoke started pouring thru my heater vents. i could no longer steer the vehicle and i put into park shut it off and left the vehicle. after we got out we could see a fire under my jeep. by the time the fire department got there my jeep was a total loss.

NHTSA ID

11726404

Incident

Mar 21, 2026

Vehicle Information: Make: Jeep Model: Wrangler Model Year: 2007 VIN: [XXX] Safety Recall Information: NHTSA Campaign ID: 16V-290 Manufacturer Recall Number: S33 Component: Airbag / Clock Spring This recall was previously performed by a dealership in February 2021; however, the vehicle is now experiencing the same symptoms the recall was intended to address, indicating the safety defect has reoccurred or was not permanently remedied. The vehicle is currently experiencing: Illuminated airbag (SRS) warning light Horn failure Traction control / electronic stability program warning light Erratic or abnormal A/C behavior that coincides with the SRS/steering wheel electrical faults These failures are consistent with a defective clock spring and directly impact the Supplemental Restraint System and other active safety systems. I contacted an authorized Jeep dealership to request inspection and repair of this recurring safety defect. The dealership confirmed the recall had been previously completed but refused to diagnose or repair the vehicle, stating in writing: “Due to company policy, we are unable to perform diagnostic or repair services on vehicles that are more than 10 years old.” They further stated that because the recall was marked as completed in 2021, they would not assist further and recommended I seek an independent repair facility. I believe this refusal violates the intent and requirements of the National Traffic and Motor Vehicle Safety Act (49 U.S.C. §§ 30118–30120), which requires manufacturers to remedy safety defects and does not allow age-based or policy-based refusal when a safety defect exists or reoccurs. This defect involves the airbag system and active safety features and presents an ongoing risk to vehicle occupants. I am requesting NHTSA’s assistance in reviewing this matter and ensuring that the manufacturer and/or authorized dealer fulfills their obligation to properly remedy this safety defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 5

NHTSA ID

11708920

Incident

Jan 5, 2026

The Bushing which attaches my shifter to the shifting cable keeps coming off/ breaking. 4 times in about 6-8 weeks. The first 3 times D N C auto repair in Ash Grove, Mo fixed for me. Today im having my Jeep towed to Corwin Dodge Jeep.

NHTSA ID

11701932

Incident

Nov 28, 2025

ABS MODULE fault Abs Traction control inoperable, no parts available, no fixes available.

NHTSA ID

11689036

Incident

Sep 22, 2025

Seatbelt will not unlatch

NHTSA ID

11682159

Incident

Aug 21, 2025

TIPM failure. Recall 07V291000 My vehicle (2007 Jeep Wrangler) is not included in the recall, although it was recalled for this model. Car suddenly had a variety of bizarre electrical malfunctions including wipers acting on their own, difficulty starting, and stalling while driving. Mechanic inspection ($150) Also contirmed that it is the TIPM. The vehicle is too dangerous to drive before the TIPM is replaced.

NHTSA ID

11674312

Incident

Jul 11, 2025

In 2022, I paid over $15,000 to an official Jeep dealership (Chrysler Dodge Jeep RAM City, Greenwich CT) to replace the engine in my Jeep Wrangler. Without clear disclosure or consent, they installed a non-OEM Jasper remanufactured engine. The invoice misleadingly stated “ALL PARTS ARE NEW UNLESS OTHERWISE INDICATED,” with no mention of Jasper or warranty terms. The vehicle began malfunctioning almost immediately, raising multiple serious safety concerns, confirmed by written service exchanges: •“The Jeep is stopping alone! Just crazy, brakes come on alone” — 🛑 Spontaneous brake engagement poses a serious crash risk. •“It also smells strong gas when turning the car on” — 🚨 Potential fuel leak or misfire, which is a fire hazard. •“The Jeep is malfunctioning,” “check engine light came back on,” “needs a PCM”, followed by: “I’m not sure this is a computer problem, but the motor you folks placed in the car.” — ⚠️ Suggests deeper integration issues between the engine and vehicle electronics. After only ~8,000 miles, the engine failed again. I spent thousands more with an independent mechanic, who found that several parts supposedly replaced in 2022 were already failing again (spark plugs, oil cooler, manifold gaskets, thermostat). This points to reused components, poor-quality parts, or improper installation. Stellantis refuses to assist, claiming their dealership is “independent,” despite operating under Stellantis branding and authorization. A Stellantis rep confirmed they would only file an internal complaint and left me to handle everything alone. This reflects mechanical negligence, brand-level accountability failures, and clear safety threats. I’m requesting NHTSA investigate: •Post-engine replacement safety hazards and quality of work and materials •Dangerous servicing practices at this authorized dealership (if not many or all of them) •Stellantis’ lack of oversight over branded repairs

NHTSA ID

11663997

Incident

Mar 11, 2022

SWITCH - CLUTCH STARTER INTERLOCK & MASTER CYLINDER ASSEMBLY - CLUTCH

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

ACTUATOR - A/C AND HEATER

ACTUATOR - A/C AND HEATER

Plate - Planetary